Panasonic TX-43LX650E Mode D'emploi page 21

for HDMI CEC (Consumer Electronic Control) function
and display the CEC device list.
Power: This menu has the same options as in TV
Options>Power menu. Check the Timer and Screen
Saver options in Settings>Device Preferences menu.
Sleep Timer: Define a time after which you want
your TV to enter sleep mode automatically. Set as
Off to disable.
Picture Off: Select this option and press OK to
turn the screen off. Press a button on the remote
or on the TV to turn the screen on again. Note that
you can not turn the screen on via the Volume +/-,
Mute and Standby buttons. These buttons will
function normally.
Switch Off Timer: Define a time after which you
want your TV to switch off automatically. Set as
Off to disable.
No Signal Auto Power Off: Set the behaviour of
the TV, when no signal is detected from the currently
set input source. Define a time after which you want
your TV to turn itself off or set as Off to disable.
Auto Sleep: Define an idle time after which you
want your TV to enter sleep mode automatically. 4
Hours, 6 Hours and 8 Hours options are available.
Set as Never to disable.
Picture
Picture Mode: Set the picture mode to suit your
preference or requirements. Picture mode can be
set to one of these options: Standard, Vivid, Sport,
Movie and Game.
Dolby Vision Modes: If Dolby Vision content is detected
Dolby Vision Bright, Dolby Vision Dark and Dolby Vision
Vivid picture mode options will be available instead of
other picture modes.
Backlight, Brightness, Contrast, Colour, HUE,
Sharpness settings will be adjusted according to
the selected picture mode.
Dolby Vision Notification: Set your notification ap-
pearance preference for Dolby Vision content. When
turned on, Dolby Vision logo will be displayed on
the screen when Dolby Vision content is detected.
Auto Backlight: Set your auto backlight preference.
Off, Low, Middle and Eco options will be available.
Set as Off to disable.
Backlight: Adjust the backlight level of the screen
manually. This item will not be available if the Auto
Backlight is not set as Off.
Brightness: Adjust the brightness value of the
screen.
Contrast: Adjust the contrast value of the screen.
Colour: Adjust the colour saturation value of the
screen.
HUE: Adjust the hue value of the screen.
Sharpness: Adjust the sharpness value for the
objects displayed on the screen.
Gamma: Set your gamma preference. Dark, Middle
and Bright options will be available.
Colour Temperature: Set your colour temperature
preference. User, Cool, Standard and Warm op-
tions will be available. You can adjust red, green and
blue gain values manually. If one of these values
is changed manually, Colour Temperature option
will be changed to User, if not already set as User.
Display Mode: Set the aspect ratio of the screen.
Select one of the predefined options according to
your preference.
HDR: Turn the HDR function on or off. This item will
be available if HDR content is detected.
Advanced Video
DNR: Dynamic Noise Reduction (DNR) is the
process of removing noise from digital or analogue
signals. Set your DNR preference as Low, Medi-
um, Strong, Auto or turn it off by setting as Off.
MPEG NR: MPEG Noise Reduction cleans up
block noise around outlines and noise on the back-
ground. Set your MPEG NR preference as Low,
Medium, Strong or turn it off by setting as Off.
Max Vivid: Manipulates contrast and colour
perception, basically converts Standard Dynamic
Range picture to High Dynamic Range picture. Set
as On to enable.
Adaptive Luma Control: Adaptive Luma control
adjusts contrast settings globally according to
content histogram in order to provide deeper black
and brighter white perception. Set your Adaptive
Luma Control preference as Low, Medium,
Strong or turn it off by setting as Off.
Local Contrast Control: Local contrast control
divides each frame to defined small regions and
provides ability to apply independent contrast set-
ting for each region. This algorithm improves fine
details and provides better contrast perception.
It makes higher depth impression by enhancing
dark and bright areas without any detail loss. Set
your Local Contrast Control preference as Low,
Medium, High or turn it off by setting as Off.
Flesh Tone: Adjusts the skin tone brightness.
Set your preference as Low, Medium, or High
to enable. Set as Off to disable.
DI Film Mode: It is the function for 3:2 or 2:2
cadence detection for 24 fps film content and
improves the side effects (like interlacing effect
or judder) which are caused by these pull down
methods. Set your DI Film Mode preference as
Auto or turn it off by setting as Off. This item
will not be available if Game Mode or PC Mode
is turned on.
English - 20 -