Technical Data; Maintenance And Storage - Yard force Easymow 260B Guide D'installation D'origine

GB

Technical Data

Model
Max cutting area
Battery pack
Switch power supply
Power supply model*
Mowing time on one charge
Rated voltage
Rated power
No load speed
Cutting width
Cutting height
Charging time
Blade model
Weight
Frequency Band
Magnetic Field Strength
Wireless Frequency Rang/Power
Max sound pressure level
Max sound power level
Degree of protection:
Robotic Mower
Switching power supply
Spare parts
Spare Blades
Boundary pegs
Boundary wire
Connectors
* WARNING: For the purposes of recharging the battery, only use the detachable supply unit
provided with this appliance.
EasyMow 260B
260 m 2
20 V/2000 mAh
Input: 100-240 V~, 50/60 Hz, 42 W
Output: 24V , CC1.5 A
FY2401500S1/FY2401500S2/FY2401500S3
60 min
20 V
42 W
3500 min -1
16 cm
Approx 20-55 mm
100 min
846210
8.2 kg
0-148.5 kHz
70 dBμA/m
2.4-2.4835 GHz/<0 dBm
L =55.8 dB, K=3 dB
pA
L =66.8 dB, K=3 dB
wA
IP24
IP67, Plug IP44
3 Pcs
100 Pcs
80 m
3 Pcs
12

Maintenance and storage

Maintenance work that has not been described in these instructions must be carried out by a
servicing agency authorised by the manufacturer. Only use original parts.
Maintenance
Check and clean your Robotic Mower regularly and replace worn parts if necessary. Preferably
use a dry brush, a damp cloth or a sharpened wooden piece.
Never use flushing water.
Following these maintenance instructions can extend your Robotic Mower's service life.
Battery Life
The Robotic Mower has a maintenance free Li-ion battery, with an estimated life of more than 2
years (depending on treatment and usage).
Winter Storage
During winter, keep your mower, docking station and power supply in a dry place.
We recommend a shed, garage or preferably store it indoors.
Prepare your device for winter storage as follows:
1. Fully recharge the battery.
2. Set the mains power switch to "OFF".
3. Thoroughly clean your Robotic Mower.
4. Unplug the power supply from the mains outlet.
5. Disconnect the power supply from the docking station.
6. Disconnect the boundary wire from the docking station. Lift up the docking station and clean.
The boundary wire can remain outside. However, it is imperative to protect the wire against
corrosion. We recommend a water-free grease or suitable sealing tape.
If available, repack the product in the original packaging.
Alternatively, our service centre offers a winter service for your device. This will include a check-up
of all parts and - if available - a software upgrade.
Preparing for spring
After winter storage, please clean the charging contacts on both the Robotic Mower and the
docking station.
Use a fine abrasion paper or a brass brush; this will help to achieve the best charging efficiency
and avoid any charging interference.
Cleaning the mower body
As your Robotic Mower is battery powered you need take care when cleaning. Remove rough dirt
with a soft brush. Use a manual water spray with mild household detergent for intensive cleaning.
Wipe off any residue after cleaning with a moist rag.
Disposal
To help the environment, please dispose of the product properly when it has reached the end of
its useful life and not in the household waste. Information on collection points and their opening
hours can be obtained from your local authority.
Li-ion Environmental damage through incorrect disposal of the batteries / rechargeable batteries.
Remove the battery pack from the product before disposal. Batteries /rechargeable batteries may
not be disposed of with the usual domestic waste. They may contain toxic heavy metals and are
subject to hazardous waste treatment rules and regulations. Please dispose of batteries according
to the relevant local requirements.
13
GB