Mythermo Bc-X10 First Setup; Settings - VISIOMED BewellConnect MyThermo BW-CX10 Mode D'emploi

8. MYTHERMO BC-X10 FIRST SETUP

- Connect the USB cable of your device to your computer to load the device. Once the loading
is over, you can unplug the cable.
- For the first use, please await 10 Minutes for the device to warm-up.
- Aim the device toward the temporal side of the forehead, as shown in the SCHEMA
2, at a distance of 3 to 5cm. Press the measurement button of the device. Temperature is dis-
played instantantaneously.
- Before each measurement, please make sure, your hair and perspiration has been removed
from your temporal forehead.
- You can then transfer your measurement in one click by pressing the transfer button, to the
Bewellconnect application and draw your temperature diagram.
- Charge the device when shows on the screen.

9. SETTINGS

9.1. CHOOSING THE TEMPERATURE MODE
The MyThermo BW-CX10 is specially designed to measure body temperature without contact, of
children or adults. It can be used by consumers in household environment and doctors in clinic
as reference. For this, use the BODY mode.
Measurement range for BODY mode: 30°C – 43°C (90°F – 109°F).
Note : You can also use the MyThermo BW-CX10 to measure the temperature of an area or an
object, food, a liquid or a room temperature. For this, use the SURFACE TEMP mode.
Measurement range for SURFACE TEMP mode: 0°C – 93.3°C (86°F - 199,9°F).
By selecting the ROOM Mode, it will display the ambient temperature of the room you are in.
Press the MODE button for one second, the screen will display: BODY for the body measurement
temperature. Press the MODE button again to switch to SURFACE TEMP or ROOM mode.
Note: The MyThermo BW-CX10 is automatically set to BODY.
Important: The surface temperature differs from the internal body temperature. To obtain the
internal temperature, always use the BODY mode.
Please make sure to select the BODY mode for an internal temperature reading and the SURFACE
TEMP mode or the ROOM mode for an external area reading (bottle, bath, room...).
9.2. CHOOSING THE TEMPERATURE UNIT
Press the °C/°F button to select the temperature unit. The symbol of the chosen temperature
unit is displayed (°C for Celsius degrees and °F for Fahrenheit degrees).
9.3. DATA MEMORISATION
It is possible to follow your temperature history directly on your smartphone ! the only thing
you have to do is to press the data transfer button, for MyThermo to transfer via Bluetooth ins-
26 BewellConnect - BW-CX10 - User Manual - 112014
BW-CX10_MANUAL_FR-UK_072015.indd 26-27
tantaneaously to your Bewell Connect Application. Please read how to install the application by
connecting yourself on our website www. Bewell-connect.com/install
9.4 ALARM SETTING - F1
Press on the measurement button to set the device on.
A PAGE
Press the °C/°F button for 3 seconds to show the menu.
F1 appears on the screen. Then alarm threshold is showed.
Alarm threshold is automatically setup on 38°C. In case of higher temperature, MyThermo BW-
CX10 will emit a beep.
To change this threshold, briefly press the Mode button to decrease it or on the °C/°F button to
increase it.
Then press °C/°F button to show the next menu (F2).
9.5. TOTAL GAP - F2
To adjust the MyThermo BW-CX10 temperature gap :
Press on the button °C/°F during 3 seconds, screen will display F1.
Press again for 3 seconds, it will display F2. Then press briefly on °C/°F in order to increase the
gap by 0,1c° or on Mode to diminish by 0,1C°
Validate your new setting by pressing the °C/°F during over 3 seconds in order to pass to menu
F3.
In case of doubt. It is advised to let the original parameter at +0,0°C
For each important ambient temperature change (+-10°), let MyThermo at the ambient tempe-
rature during at least 15 Minutes before its use, in order to let the device acclimate and recali-
brate.
9.6 ADD OR SUPPRESSION OF THE SOUND BIP F3.
Press on the measurement button to set the device on.
Then press on the button °C/°F during 3 seconds, screen will display F1.
Press again for 3 seconds, it will display F2.
Press again for 3 seconds, it will display F3.
Press the button for °C/°F or the Mode button. Screen displays 0 when the sound is inactivated
and 1 when activated.
9.7 EXIT THE CONFIGURATION MODE.
Press during 3 seconds on button °C/°F in order to validate the changes in the parmaeters and
exit the menu. LCD displays END and then switches off.
BewellConnect - BW-CX10 - User Manual - 112014 27
13/07/2015 17:11