Tools Needed - Pingi VIDA 2 Mode D'emploi

EN
VIDA 2 - CXTV-N1000EU - DEHUMIDIFIER SET
BOX CONTENT
1. .
2
. .
3 4
INTENDED USE
Your new Pingi Vida 2 Dehumidifier set (CXTV-N1000EU) is suitable for dehumidifying enclosed indoor
spaces. The appliance is powered by the 9V AC-DC adapter that is supplied with the device. The power
adapter operates on 100-240V, 50/60Hz (mains electricity). Never try to connect the device or power adapter
to other power sources. Please always follow the safety instructions in this manual. Keep this instruction
manual in a safe place, so that it is available at all times. This product complies with regulatory, national and
European requirements. Never try to make technical modifications to this device. We do not accept liability
for accidents or damages resulting from failure to follow these operating and safety instructions.
FUNCTION AND APPLICATION
The Pingi Vida 2 Dehumidifier set (CXTV-N1000EU) was developed as a compact dehumidifier set that
captures excess moisture in indoor spaces. This product is ideally suited for unventilated indoor spaces. The
captured moisture is collected in the integrated tank.
WHAT TO EXPECT
The Vida 2 is a thermoelectric dehumidifier. The performance of this type of dehumidifier depends on
the amount of water in the air. The higher the air temperature, the more water air can contain (relative
humidity). At high room temperatures, the device needs to work a lot harder, and it has to remove more
moisture to decrease the relative humidity level. Vida 2 will then collect up to 250ml of water per day, and
you might need to empty out the water tank often. In a colder room, there will be less water to capture, and
the tank will fill more slowly. Is room temperature <10°C? There will not be much moisture in the air, and
the tank will fill only slowly.
BEFORE YOU START
Please carefully read the safety instructions on the front page of this manual before getting
started.
WALL MOUNT INSTALLATION
6mm
This set comes with an included wall mount, model VSB-1S. Use of the wall mount is optional -
the appliance can also be used without it.
To use the wall mount, it needs to be securely installed on a vertical surface by means of 3 screws.
1. Select a vertical surface that provides sufficient distance to the wall mount and other objects.
2. Important: Make sure the power adapter cable can easily reach a nearby wall outlet before installing the
wall mount.
OK
3. Check if the wall mount hangs securely in a vertical position. Use a level if necessary to ensure it hangs
straight. Use a screwdriver to install the screws.
.
6
.
5
1. Dehumidifier
2. Wall mount (VSB-1S)
3. Drainage tube
4. Power adapter
5. Wall plugs and screws
6. Operating instructions

TOOLS NEEDED

For wall mount installation only.
6mm
4. Before placing the appliance on the wall mount: Push the DC connector of the adapter through the
right opening underneath the wall mount. Optionally do the same with the drainage tube on the left side.
5. Plug the DC connector into the device. Optionally attach the drainage tube to the device. Now place the
appliance on the mount and make sure it is properly secured.
OPERATION
Make sure the ON/OFF switch on the back of the appliance is in the ON position.
Normal: You can activate Normal mode by touching the main button on the front of the device once. The
button will pulse blue. The tank light will be activated. The appliance is now collecting humidity from the
ambient air.
Turbo: Touching the main button on the front of the device again will activate the turbo mode. The main
button will continuously light blue. The device will operate at its maximum speed.
Night: Touching the main button a third time will activate night mode, which reduces the fan speed and
switches off all light.
Tank full: This appliance has an automatic shut-off function. When the tank is nearly full, the tank light will
change colour to red, and the power button light will dim.
ON/OFF switch
EMPTYING THE TANK
This device has a tank with a capacity of approximately 1000ml. When the tank is nearly full, the appliance
will automatically shut off its dehumidifying functions and the tank light will change colour to red. Switch
off the appliance and carefully slide out the tank by pulling its handle. The small cap marked 'DRAIN TANK'
located on top of the tank can now be removed. Empty the tank into, for example, a kitchen sink. After
draining the tank, it can be replaced. The device can now be switched back on.
24/7 DRAINAGE
This appliance comes with a convenient 24/7 drainage option. You can attach a 10mm drainage tube to
the tank and any collected water will flow out through the drainage tube. You can hang the other end of the
Blue light