Power Amp - Fender Bassman 1200 Mode D'emploi

CC. PARALLEL SPEAKER JACKS – Use a
total speaker load of 2Ω for the most
efficient transfer of power.
cabinets, two 4Ω cabinets or one 2Ω
cabinet have the ideal speaker load of
2Ω. Connect speakers only when the
power is switched OFF.
DD. POWER SUPPLY CORD – Connect the
unit to a grounded AC receptacle in
accordance with the
frequency ratings as shown on the rear panel.
EE. EFFECTS LOOP JACKS – Connections for an external
effects loop. Connect Send to the input of your effects
device and Return to the output of the effects device.
FF. TUNER OUT JACK – Connection for an electric bass guitar
tuner. Press IN the Tuner Only button for silent tuning.
GG. FOOTSWITCH JACK – Connection for the 3-button
footswitch (use unshielded speaker type cable).
footswitch provides remote switching of channel selection,
equalization and compression.
footswitch overrides the corresponding front panel controls.
R R a a c c k k M M o o u u n n t t
R R a a c c k k M M o o u u n n t t
The Bassman ® 1200 is designed for rack
mounted operation and flight-case
mounted transportation.
nut driver with the included hardware:
1) Loosely attach the rear rack mount
ears to the "T" bracket using the
supplied bolts.
TYPE:
PART NUMBER:
POWER REQUIREMENTS:
PRE AMP INPUT IMPEDANCE:
FULL POWER SENSITIVITY:
TONE CONTROLS:
GRAPHIC EQUALIZER:

POWER AMP

INPUT IMPEDANCE:
RECOMMENDED SPEAKERS:
DIMENSIONS
WEIGHT:
B B a a s s s s
B B a a s s
Four 8Ω
PARALLEL SPKR JACKS
2 Ω minTOTAL
voltage and
When connected, the
E E a a r r s s 2) Support the Bassman
E E a a r r s s
four corners are attached to avoid
bending the rack rails.
3) Align the front rack mount ears with
Use a 7/16"
the rack rails and attach using the
bolts provided.
4) Slide the rear rack mount ears to
adjust them to fit the depth of the
rack, then attach using the bolts
provided.
S S p p e e
S S p p
PR 348
021-3302-010 (120 V, 60 Hz) US
021-3332-010 (240 V, 50 Hz) AUS
021-3352-010 (220 V, 50 Hz) ARG
021-3372-010 (100 V, 50 Hz) JPN
1800 W
470 kΩ
12.75 mV
Treble: ±15 dB @ 3 kHz
±12 dB @ 31.5 Hz, 63 Hz, 125 Hz, 250 Hz, 500 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz.
MID NOTCH: –20 dB @ 700 Hz
LOW BOOST: +10 dB @ 40 Hz
HIGH BOOST: +10 dB @ 6 kHz
10 kΩ
1200 W R.M.S. into 2 Ω @ < 0.2 % T.H.D.
POWER OUTPUT:
SENSITIVITY: 1 V R.M.S. (0 dBv)
Bassman
HEIGHT: 3.5 in
WIDTH: 19.0 in
DEPTH: 15.0 in
35 lb
Product specifications are subject to change without notice.
m m a a n n ® ® 1 1 2 2 0 0 0 0
® ®
s s m m a a n n 1 1 2 2 0 0 0 0
1200W
1800W
RETURN
HH. POWER AMP PASS-THROUGH JACK- Output connection
for linking multiple Bassman
a standard TS (tip-sleeve) patch cord to connect this jack to
the Effects Loop Return jack on the auxiliary amplifier.
II. LINE OUT JACKS – Transformer balanced, line-level
connections for output to sound reinforcement or recording
equipment. Both the XLR and the 1/4 inch TRS (tip-ring-
sleeve) jacks include a bass speaker emulation circuit. Front
panel tone adjustments are included or bypassed using the
Line Out button.
The
® 1200 until all
c c i i f f i i c c a a t t i i o o n n s s
e e c c i i f f i i c c a a t t i i o o n n s s
® 410H Pro or Bassman ® 215 Bass Loudspeaker Enclosures
(8.9 cm)
(48.3 cm)
(38.1 cm)
(15.9 kg)
7
EFFECTS
TUNER FOOT
LOOP
OUT SWITCH
SEND
® 1200 amplifiers together. Use
Bassman ® Rear Rack
1200 Mount Ears
"T"
Bracket
021-3312-010 (110 V, 60 Hz) TW
021-3342-010 (230 V, 50 Hz) UK
021-3362-010 (230 V, 50 Hz) EUR
021-3392-010 (220 V, 60 Hz) ROK
Bass: ±15 dB @ 40 Hz
LINE OUT
POWER AMP
PASS THROUGH
Rear Rack
Rail