Publicité
Les langues disponibles
Les langues disponibles
3 HOLE INSTALLATION NO SIDE SPRAY
5
5A
%27720 *5229(
5 INSTALLING DECKPLATE
Ensure that the Plastic Putty Plate (5A) is pressed on the Deckplate (5B). Place
a bead of plumber's putty in the groove along the outer edge of the Putty Plate
(5A). Install the Deckplate (5B) over the three holes in your sink.
6
6C
6A
6 SECURING DECKPLATE TO DECK
)URP XQGHUQHDWK VLQN KDQG WLJKWHQ :LQJ 1XWV 6A) to Mounting Posts (6C).
Caution: do not over-tighten wing nuts. Remove any excess putty from
around the outside edge of Deck Plate (6B).
STOP
3 HOLE INSTALLATION WITH SIDE SPRAY
7
7A
%27720 *5229(
7 INSTALLING DECKPLATE
Ensure that the Plastic Putty Plate (7A) is pressed on the Deckplate (7B). Place
a bead of plumber's putty in the groove along the outer edge of the Putty Plate
(7A). Install the Deckplate (7B) over the three holes in your sink.
8
8A
8B
8D
5B
6C
6B
6A
Go To Step 17
7B
8A
8D
8G
8E
(1*/,6+
8 SECURING DECKPLATE & HOSE GUIDE
Insert Hose Guide (8A) into the side hole in the Deckplate (8B) and onto the
sink hole. Align the hose guide Tabs (8C) to those in the Deckplate Hole (8D).
)URP XQGHUQHDWK VLQN VHFXUH WKH +RVH *XLGH 8A) by screwing the Plastic
Locknut (8D 6HFXUH 'HFNSODWH 8E) by screwing Wing Nut (8F) to Mounting
Post (8G). Hand tighten. Caution: do not over-tighten. Remove any excess
putty from around the outside edge of Deckplate (8E).
9
9 SIDE SPRAY INSTALLATION
,QVHUW WKH 6LGH 6SUD\ +RVH 9A) through the Hose Guide (9B )URP XQGHUQHDWK
VLQN IHHG WKH 6LGH 6SUD\ +RVH 9A) back up through the center hole of sink
and through Deckplate (9C) so that it is above the sink.
10
10 INSTALLING MOUNTING RING & GUIDE FLANGE
Place Mounting Ring (10A) over Plastic Gasket (10B) and sink hole. If desired,
SODFH D VPDOO EHDG RI SOXPEHU¶V SXWW\ WR WKH XQGHUVLGH RI WKH +RVH *XLGH )ODQJH
(10C). Align both Mounting Ring (10A DQG +RVH *XLGH )ODQJH 10C) to the
center of sink holes.
11
8C
8B
11 SECURING HOSE GUIDE
)
Insert Hose Guide (11A LQWR +RVH *XLGH )ODQJH 11B) and onto the sink hole.
)URP XQGHUQHDWK VLQN VHFXUH WKH +RVH *XLGH 11A) by screwing the Plastic
Locknut (11C). Hand tighten.
9A
9B
STOP
Go To Step 16
2 HOLE INSTALLATION
(For T34-4T Models Only)
10C
11A
11B
9C
10A
10B
11C
Publicité
