Auto Mode; Turbo Mode - Tectro TBH 570-2 Manuel D'utilisation

4.
ECONO SEND
TURBO
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2

AUTO MODE

In this mode, the stove uses the difference between the desired temperature and
the room temperature itself to calculate the required output. To select auto mode,
press (1) until the
ECONO SEND
end auto mode, press
TURBO
ECONO
(2). See figure 7.
ECONO SEND
AUTO
ON 1 OFF 1
TURBO
TURBO
ON 2 CANCEL OFF 2
ON 1 AUTO OFF 1

TURBO MODE

ON 2 CANCEL OFF 2
In Turbo mode, the stove operates at maximum power for 30 minutes. In Turbo
mode the temperature is pre-set to 30ºC. After 30 minutes, the stove returns to the
mode before the Turbo mode was activated. To select Turbo mode, hold down the
ECONO SEND
button (1) for more than 2 seconds, and then push
TURBO
ON 1 AUTO
OFF 1
mode, hold down the
ON 2 CANCEL OFF 2
disappear from the remote control display and be replaced by the output level and
the set temperature. Press
ECONO MODE
In Econo mode, the temperature remains constant. Every 10 minutes the stove
adjusts the power until heat output level 1 is reached. To select Econo mode, hold
down the button (1) for more than 2 seconds, until Econo appears in the dis-
ECONO SEND
play (2) and then push TURBO
ECONO
ON 1 AUTO
OFF 1
TURBO
(1) for at least 2 seconds. The word Econo will disappear from the remote control
ON 2 CANCEL OFF 2
ON 1
display (2). Press (3) to confirm your choice. See figure 9.
ECONO SEND
ON 2
TURBO
ON 1 AUTO
PROGRAMME 1 (ON1 AND OFF1)
ON 2 CANCEL
1. The desired switch-on and switch-off timer must be set when the
remote control is switched off.
2. The stove retains the temperature and heat output settings it had
before being switched off.
3. The minimum period of time between switching off and switching on
is 20 minutes. This is the time needed for the stove to complete the
cooling-down phase.
4. After a brief power interruption, the timer mode will have to be set
again.
ECONO SEND
ACTIVATE AUTOMATIC MODE (ON1)
TURBO
Press button (1) to switch on the stove according to programme 1. The time AUTO
ON 1
ON 2 CANCEL
and ON1 symbol will flash on the remote control. Use the buttons
(2&3) to select the desired time (10-minute intervals). To confirm, choose
The desired activation time is shown in the remote control. Press
The display (5) on the stove will show Chrono. See figures 10 and 11.
ECONO SEND
DEACTIVATE AUTOMATIC MODE (OFF1)
TURBO
Press button ON 1 AUTO OFF 1 (1) to switch off the stove according to programme 1. The time
ON 2 CANCEL OFF 2
and OFF1 symbol will flash on the remote control. Use the buttons
(2&3) to select the desired time (10-minute intervals). To confirm, choose
The desired deactivation time is shown in the remote control. Press
symbol appears. Press
ECONO
TURBO
(1) again, select the desired output and confirm with
ON 1
SEND
ON 2
AUTO
ON 1 OFF 1
ON 2 CANCEL OFF 2
ECONO SEND
button (1) for at least 2 seconds. The word Turbo (2) will
TURBO
ON 1 AUTO
OFF 1
CANCEL
ON 2 OFF 2
(3) to confirm your choice. See figure 8.
ECONO SEND
TURBO
ON 1 AUTO
OFF 1
ON 2 CANCEL OFF 2
(3). To deactivate this mode, hold down the
SEND
AUTO OFF 1
CANCEL OFF 2
OFF 1
OFF 2
OFF 1
OFF 2
(2) to confirm your choice. To
SEND
AUTO
OFF 1
CANCEL OFF 2
(3). To deactivate this
ECONO SEND
TURBO
AUTO
ON 1 OFF 1
ON 2 CANCEL OFF 2
ECONO
TURBO
ON 1
ON 2
ECONO SEND
and
TURBO
ECONO SEND
ON 1 AUTO
TURBO
ON 2 CANCEL
AUTO (4) to confirm.
ON 1 OFF 1
ECONO SEND
ON 2 TURBO CANCEL OFF 2
AUTO
ON 1 OFF 1
ON 2 CANCEL OFF 2
ECONO SEND
ECONO SEND
and
TURBO
ECONO SEND
TURBO
AUTO AUTO
ON 1 ON 1
TURBO
ON 2 CANCEL
ON 2 CANCEL
ON 1 AUTO (4) to con-
OFF 1
ECONO SEND
TURBO
ON 2 CANCEL OFF 2
ON 1 AUTO
OFF 1
ON 2 CANCEL 4 OFF 2
151
button
SEND
AUTO
OFF 1
CANCEL OFF 2
ECONO SEND
TURBO
ON 1 (1). AUTO
OFF 1 OFF 1
ON 2 CANCEL OFF 2
OFF 2
OFF 1 (1). OFF 1
OFF 2
OFF 2