Ryobi ART-3 Manuel D'utilisation page 10

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
GB
FR
DE
ES
OPERATION
PREPARING FOR OPERATION (Fig. 14)
Unplug the router table.
Q
Always plug the router into table switched outlet.
Q
Never plug a router table mounted router into another
power source.
Direction of feed of the workpiece is from right to left
Q
or from the back of the router toward the front with the
bit located in the fence opening.
WARNING
Failure to unplug your router could result in
accidental starting causing possible serious
injury.
Direction of feed must always be so that the
Q
workpiece is being thrust against the sharp edges of
the rotating bit.
The workpiece must always be tight against the
Q
guide fence, unless a ball-bearing piloted bit is being
used. The infeed fence should be adjusted to support
the uncut workpiece while the outfeed fence should
be adjusted properly to support the workpiece after
the cut passes the router bit, compensating for the
removed stock.
FITMENT OF THE TABLE EXTENSION (Fig. 14)
Using the Nuts and washers provided in the bag fit
Q
the extension bar to the table using the 2 holes at the
table ends. Ensure the male threaded end is used.
Fit both extension bars. Using the flats at the end of
Q
each extension bar (nearest the Router table) tighten
using the spanners provided.
Slide the extension table over the extension bars
Q
ensuring the name is facing you, and located towards
the rear of the table.
Using the screws provided in the bag screw the table
Q
to the extension bars and tighten.
To remove, reverse the mounting instructions.
Q
FITMENT OF THE TABLE DUST EXTRACTION
SYSTEM
After fitment of the guide piece (see separate
Q
description).
Place the black part of the dust extraction module in
Q
the centre of the guide piece and align the 4 screw
holes on the dust extraction module to the 4 screw
holes on the guide piece.
Using the 4 screws provided in the bag screw the
Q
dust extraction module in place securely.
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
English
If using a 31mm diameter extraction hose, insert the
Q
sleeve (14) (Fig 12) into the rear of the dust extraction
module.
If using a 57mm diameter hose, remove the insert
Q
from the rear of the dust extraction module.
IMPORTANT
Lock the router switch by clamp which is provided
Q
together with router table packaging. (Fig 15)
Always control the power to the router with router
Q
table switch whenever the router is mounted on the
table.
MAINTENANCE
WARNING
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.
come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
CAUTION:
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
WARNING
Always begin any maintenance procedure by
disconnecting the router table from the power
supply to avoid risk of serious personal injury.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts.
Q
Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged
by their use. Use clean cloths to remove dirt, carbon
dust, etc.
Periodically check all clamps, nuts, bolts and screws
Q
for tightness and condition. Make sure that the throat
guard, safety guard,and undertable guards are
properly positioned and securely attached.
ENVIRONMENTAL PROTECTION
6
HU
RO
LV
LT
EE
Do not dispose of in general household
waste. Instead, dispose in an environmentally
friendly way. Contact your local recycling
centre or council for advise. Ryobi takes the
care of the environment very seriously.
HR
SI
SK
GR
TR

Publicité

Table des Matières
loading

Table des Matières