Woods BRUSHBULL BB48XE Manuel D'utilisation page 27

1. D
riveline shield
2. Input shaft (slot)
3. 1/2 NC Lock nut
4. 1/2 NC x 3" Cap screw GR2 - Shear Bolt (12.7 x 76.2 mm)
5. Clutch shield
6. Retaining ring
7. M8 x 1.25P x 20 mm Cap screw
8. 5/16 Lock washer
9. 5/16 Flat washer
Figure 36
. Shear Bolt Driveline Assembly
(BB48XE & BB60XE Standard)
Driveline Slip Clutch -
Optional on BB48XE & BB60XE
NOTICE
■
A grade 8 bolt must be used to attach clutch driveline to gearbox.
A new slip clutch, or one that has been in storage over the winter, may seize.
1.
Before operating slip clutch, make sure it will slip. Refer to Slip Clutch
Adjustment (Figure 15), page 14.
2.
Position clutch shield (3) against gearbox. Secure using cap screw (4),
lock washers (5), and flat washers (6). Torque hardware to 12 lbs-ft.
3.
Install driveline onto gearbox input shaft and secure with bolt (1) and nut
(2).
4.
Secure driveline with bolt (1) and nut (2).
5.
Lubricate rear driveline half and install front driveline half.
6.
Attach tether chain to diagonal brace bar.
1. 1/2 NC x 3" Cap
screw GR8 (Clutch)
(12.7 x 76.2 mm)
2. 1/2 NC Lock nut
3. Clutch shield
4. M8 x 1.25P x 20 mm Cap screw
5. 5/16 Lock washer
6. 5/16 Flat washer
Figure 37
. Slip Clutch Driveline Assembly
(BB48XE & BB60XE Optional)
(BB72XE & BB84XE Standard)
MAN1254 (3/16/2018)
Driveline Slip Clutch - BB72XE & BB84XE
1.
Before operating slip clutch, make sure it will slip. Refer to Slip Clutch
Adjustment (Figure 15), page 14.
2.
Position clutch shield (3) against gearbox. Secure using cap screw (4),
lock washers (5), and flat washers (6). Torque hardware to 12 lbs-ft.
3.
Install driveline onto gearbox input shaft and secure with bolt (1) and nut
(2).
4.
Secure drive by releasing lock collar slide onto the gearbox shaft and
release lock collar when balls are seated into groove. Pull on drive to
insure drive is secure.
INSTALL SAFETY SHIELDING
Optional Chain Shielding

Full chain, rubber, or steel band shielding must be installed when
operating in populated areas or other areas where thrown objects could
injure people or damage property.
• If this machine is not equipped with full chain, rubber, or steel
band shielding, operation must be stopped when anyone comes
within 300 feet (92 m).
• This shielding is designed to reduce the risk of thrown objects.
The mower deck and protective devices cannot prevent all objects
from escaping the blade enclosure in every mowing condition. It is
possible for objects to ricochet and escape, traveling as much as 300
feet (92 m).
The optional chain shielding assemblies are ready for installation when you
receive them.
1.
Refer to Front & Rear Chain Shielding, page 35, and attach as shown
by inserting the bolts from inside the cutter frame out through the
shielding.
2.
Install hardware as shown in the parts drawing.
Rubber Deflector
Attach rubber deflector (1) and link (2) to front of cutter using carriage bolts (3)
and flange lock nuts (4).
Figure 38
. Rubber Deflector Installation
Assembly 27
1. Rubber deflector
2. Link
3. 3/8 NC x 1 Carriage
bolt
4. 3/8 NC Flange lock nut