Table des Matières
Publicité
GENERAL
Carefully read the following important information regarding
installation safety and maintenance. Keep this information
booklet accessible for further consultations.
The appliance has been designed for use in the ducting version
(air exhaust to the outside – Fig.1B), filtering version (air
circulation on the inside – Fig.1A).
SAFETY PRECAUTION
Take care when the cooker hood is operating
simultaneously with an open fireplace or burner that depend
on the air in the environment and are supplied by other than
electrical energy, as the cooker hood removes the air from the
environment which a burner or fireplace need for combustion.
The negative pressure in the environment must not exceed 4Pa
(4x10-5 bar). Provide adequate ventilation in the environment
for a safe operation of the cooker hood. Follow the local laws
applicable for external air evacuation.
Before connecting the model to the electricity network:
- Control the data plate (positioned inside the appliance) to
ascertain that the voltage and power correspond to the network
and the socket is suitable. If in doubt ask a qualified electrician.
- If the power supply cable is damaged, it must be replaced with
another cable or a special assembly, which may be obtained
direct from the manufacturer or from the Technical Assistance
Centre.
Warning !
In certain circumstances electrical appliances may be a
danger hazard.
A) Do not check the status of the filters while the cooker
hood is operating
B) Do not touch bulbs or adjacent areas, during or straight
after prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker
hood
D) Avoid free flame, as it is damaging for the filters and
a fire hazard
E) Constantly check food frying to avoid that the
overheated oil may become a fire hazard
F) Disconnec t the elec trical plug prior to any
maintenance.
G) This appliance is not intended for use by young children
or infirm persons without supervision
H) Young children should be supervised to ensure they do
not play with the appliance
I) There shall be adequate ventilation of the room when
the rangehood is used at the same time as appliances
burning gas or other fuels
L) There is a risk of fire if cleaning is not carried out in
accordance with the instructions.
This appliance conforms to the European Directive EC/2002/96,
Waste Electrical and Electronic Equipment (WEEE). By making
sure that this appliance is disposed of in a suitable manner, the
user is helping to prevent potential damage to the environment
or to public health.
ENGLISH
The symbol on the product or on the accompanying
paperwork indicates that the appliance should not be
treated as domestic waste, but should be delivered to a
suitable electric and electronic appliance recycling
collection point. Follow local guidelines when disposing of waste.
For more information on the treatment, re-use and recycling of
this product, please contact your local authority, domestic waste
collection service or the shop where the appliance was
purchased.
INSTALLATION INSTRUCTIONS
Assembly and electrical connections must be carried out by
specialised personnel.
• Electric Connection
The appliance has been manufactured as a class II, therefore
no earth cable is necessary.
The plug must be easily accessible after the installation of the
appliance.
If the appliance is equipped with power cord without plug, a
suitably dimensioned omnipolar switch with 3 mm minimum
opening between contacts must be fitted between the
appliance and the electricity supply in compliance with the
load and current regulations.
The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral
• If the hob is electric, gas, or induction, the minimum distance
between the same and the lower part of the hood must be at
least 45 cm.
If a connection tube composed of two parts is used, the upper
part must be placed outside the lower part. Do not connect the
cooker hood exhaust to the same conductor used to circulate hot
air or for evacuating fumes from other appliances generated by
other than an electrical source.
• In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which has
the same diameter as the air exhaust outlet hole. If a pipe
with a smaller diameter is used, the efficiency of the product
may be reduced and its operation may become noisier.
• Before starting to fix the hood, disconnect the anti-grease
filter B (Fig.5) for easier appliance handling.
Before this operation, perform the following steps depending
on the model purchased:
MODEL 1
Remove the 3 panels A as shown in Fig.4a.
Pull handle B as shown in Fig.5.
MODEL 2
Open panel C as shown in Fig.4b.
Pull handle B as shown in Fig.5.
• Wall fixing
Mark the position of the lower side of the hood on the wall
(Fig.2A). Maintain the minimum distance required from the hob
as shown in Fig.2B.
- Position the fixing template on the wall, making sure that the
line coincides with the line previously made on the wall.
- Mark the fixing holes and cut them into the material (Fig.3).
- 27 -
GB
Publicité
Table des Matières
