Cleaning And Maintenance - Excel XLERATOR Manuel D'installation Et De L'utilisateur

R E A D A N D S AV E T H R E A D A N D S A V E T H E S E I N S T R U C T I O N S
OUTSIDE: Loosen dirt and grime by gently washing the cover (including air inlet holes). Use a soft cloth or sponge and a mild soap or
detergent with lukewarm water.
INSIDE: Excel recommends to inspect and clean the inside of the dryer as required at least once per year, or if performance
diminishes. Heavier usage, or an environment that contains excessive lint, dust or other particles, will require more frequent cleaning.
Lint on the air inlet, the Pre-Filters (Dryer or HEPA if so equipped), or other internal parts of dryer will reduce efficiency and shorten the
life of the working parts. To clean, shut off power to dryer at service connection. Remove Cover by unscrewing the 2 Tamper-Proof Bolts
from side of Cover with the special Tamper-Proof Wrench provided with each dryer. Use a small, soft brush to gently clean all parts. If
your unit contains a dryer Pre-filter or HEPA Filtration System, unclip the Pre-Filter, rinse the Pre-Filter with water and dry. Re-install.
DO NOT CLEAN THE HEPA FILTER OR ALLOW IT TO COME INTO CONTACT WITH WATER.
Dryer does not turn on
1. Check power to the unit and connections. Verify dryer is receiving correct voltage 1.
at Terminal Block. (Check the voltage on dryer tag).
2. Locate and check the RED service LED light next to air outlet on bottom of dryer
for the following conditions:
Light is ON – Place hands under Sensor. If light stays on, then replace Sensor.
If light goes off, check to make sure wiring is correct. If OK, check wire
connecting to Motor. If both are OK, replace Motor.
Light is OFF – Check for loose, disconnected or improper wiring (See wiring
schematic on blower housing) or replace Control Assembly.
Light is FLASHING – See error codes in CODE chart
Dryer does not shut off
1. May be mounted too close to a counter or object (adjust Sensor range).
2. Check for loose, disconnected or improper wiring at Control Assembly (refer to
wiring schematic affixed to blower housing.
3. Replace Control Assembly.
The dryer is shipped with maximum heat and maximum motor speed. To adjust, turn the corresponding knob
COUNTERCLOCKWISE to reduce.
Note: Eco® models have no heating element and are set with heat at minimum.
If problems cannot be resolved with the above troubleshooting steps, please call the manufacturer
at 1-800-255-9235 and one of our trained technicians will be happy to assist you.
Codes are displayed by the flashing of the red LED light in the sensor behind air outlet.
Normal operation will be indicated by the red LED being on when not drying and off when hands are under the sensor.
DRYER MAINTENANCE CODES
1 SHORT / 1 LONG FLASH
1 SHORT / 2 LONG FLASH
2 SHORT / 1 LONG FLASH
MOTOR PROBLEM CODES
1 LONG / 3 SHORT FLASH
1 LONG / 4 SHORT FLASH
HEATER PROBLEM CODES
2 LONG / 3 SHORT FLASH
E X C E L D R Y E R , I N C
3 5 7 C H E S T N U T S T R E E T, E A S T L O N G M E A D O W , M A 0 1 0 2 8

CLEANING AND MAINTENANCE

ADJUSTING THE HEAT OUTPUT, MOTOR SPEED AND SENSOR RANGE
H = HEAT
Clogged Pre-Filter
Severely clogged Pre-Filter
In Lockout Mode
Motor Over Current
Motor Under Current
Shorted or incorrect Heater
1 . 8 0 0 . 2 5 5 . 9 2 3 5 E X C E L D R Y E R . C O M
I N S T R U C T I O N S
TROUBLESHOOTING
Dryer blows only cold air (non-ECO dryers)
Check heat setting on control.
2. Check for loose connections to Heating Element.
3. Replace Heating Element.
Dryer does not always turn on, or turns on by itself
1. May be mounted too close to counter or object (adjust Sensor range).
2. Check for foreign material on Optical Sensor next to Air Outlet.
3. Check for loose wires on Control Assembly.
4. Replace Control Assembly.
Dryer has loss of air volume
1. Check motor speed setting (Labeled "M") on control. Turn clockwise to increase.
2. Check for slow running Motor or burning smell. If so, replace Motor.
3. Check Pre-Filter for lint buildup. Clean by removing Pre-Filter and rinse in warm
water then dry Pre-Filter before reinstalling.
4. Check for any cracks in plastic housing.
M = MOTOR
CODE CHART
Remove and clean Pre-Filter
Remove and clean Pre-Filter
Remove obstruction or adjust
sensor range
Measure voltage across the
Terminal Block. If OK,
replace Motor
Measure voltage across the
Terminal Block. If OK,
replace motor
Replace Heating Element
A D M I N @ E X C E L D R Y E R . C O M
R = RANGE
Dryer will continue to run
Dryer will stop
Dryer will stop until obstruction
cleared or sensor range is adjusted
Dryer will stop
Dryer will stop
Dryer will stop
7 / 2 0 1 7 3