Table Des Matières; Start Here; Preparation - Emerson InSinkErator indulge Serie Manuel Du Propriétaire

START HERE

proper installation shoUlD take aBoUt 2-4 hoUrs
1

PREPARATION

a
Required minimum from
center of hole to wall
F-HC1100 ................2 ⁄
5
8
F-GN1100 ................3 ⁄
1
4
F-HC2200 ................2 7 ⁄
8
F-GN2200 ................3 ⁄
1
2
F-HC2215 ................2 ⁄
7
8
F-GN2215 ................3 ⁄
1
2
F-HC3300 ................2 ⁄
1
2
F-H3300 ...................2 1 ⁄
2
Maximum counter thickness is 3".
The wall outlet for your dispenser must have power supplied to it continuously
and must be fused. It should not be controlled by the same wall switch
that operates your disposer, unless using an InSinkErator SinkTop Switch
b
If you have to drill through sink or
countertop, you may need to rent or purchase
the appropriate tools.
c
Required Hole Size
F-HC1100 ................1 ⁄ " - 1
3
8
F-GN1100 ................1 ⁄ " - 1
1
4
F-HC2200 ................1 ⁄ " - 1
3
8
F-GN2200 ................1 ⁄ " - 1
1
4
F-HC2215 ................1 3 ⁄ " - 1
8
F-GN2215 ................1 ⁄ " - 1
1
4
F-HC3300 ................1 ⁄ " - 1
3
8
F-H3300 ...................1 3 ⁄ " - 1
8
Consult a professional before drilling into
a surface other than stainless steel.
6
Identify locations for the dispenser
faucet, tank and filter.
"
Check to make sure there is proper
"
clearance for dispenser handles to
"
be fully opened.
"
"
Check to make sure counter is 3"
"
thick or less.
"
Make sure there is a grounded
"
electrical outlet under the sink.
Turn off water supply.
If using the sink sprayer hose hole,
remove nut that connects sprayer
hose at bottom of faucet.
Using adjustable wrench, remove nut
connecting sprayer washer flange in
sprayer hole.
Plug hose opening with either a 1/8"
plug or a 1/4" cap (not supplied).
What if you don't have a sprayer hole or
⁄ "
1
don't want to use it?
2
⁄ "
1
2
Many homeowners replace the soap
⁄ "
1
2
dispenser in their sink with an instant
⁄ "
1
2
hot water dispenser.
1 ⁄ "
2
⁄ "
1
If drilling a hole into a stainless steel
2
⁄ "
1
sink or counter top, you can cut a
2
1 ⁄ "
mounting hole for the dispenser with a
2
hole saw for stainless steel, or you can
use a hole punch.
2
INSTALLINg THE FAUCET - 1100/2200
a
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
b
.
TM
Make sure to use rubber O-ring
to ensure proper seal.
c
To ease feeding of tubes through hole,
first insert blue tube with quick-connect
attachment and then insert the remaining tubes.
1
d
Semi-circular mounting plate should
encircle all descending tubes and
extend beyond sink hole when tight.
Unpack dispenser components.
On a firm, flat surface, carefully
straighten the copper tubing.
Ensure that the black O-ring is
properly seated in the base of the
dispenser head (the groove on the
underside of the dispenser).
Feed tubes down through the hole
in the sink or countertop until the
base is at rest on the sink or
countertop surface.
An assistant may be needed to
hold the dispenser head in place while
securing the dispenser.
2
From under the sink, place the
semi-circular mounting plate onto
the threaded stud.
Place hex nut onto the threaded stud.
Ensure faucet head is at desired angle.
Insert screwdriver into hole on side of
hex tool (creating a "T"), and use tool
3
to tighten nut and secure faucet.
1
P
1
7