Table des Matières
Publicité
EHT 55/650 PLUS | EHT 61/750 PRO
PRODUCT SPECIFICATIONS
INTENDED USE
This product is intended for cutting and trimming of
hedges, bushes and shrubs in domestic gardens. The
maximum cutting capacity must be observed. Do not
cut branches exceeding the stated maximum capacity.
The use of this product in case of rain or humid envi-
ronment is prohibited. For safety reasons it is essen-
tial to read the entire instruction manual before first
operation and to observe all the instructions therein.
This product is intended for private domestic use
only, not for any commercial trade use. It must not be
used for any purposes other than those described.
TECHNICAL DATA
Article Number
Model - EST
Rated voltage
Rated power input
No Load Speed
Cutting length
Blade thickness
Tooth gap
Weight
Sound emission values determined according to
EN 60745-1, 60745-2-15
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Guaranteed sound
power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to EN
60745-1, 60745-2-15
Vibration level max:
a
h , front handle
a
h , rear handle
K
43 287
42 411
55/650
61/750
PLUS
PRO
V
230 - 240
Hz
50
W
650
750
min
1.500
1.500
-1
mm
550
610
mm
1,8
1,8
mm
24
Kg
3,3
3,8
dB(A)
91,52
86,5
dB(A)
98,15
102,7
dB(A)
101
108
dB
3
4,276
(triax vector sum)
h
m/s
3,376
4,276
2
m/s
2,912
3,793
2
m/s
1,5
1,5
2
IDENTIFICATION
1. Blade
2. Front guard
3. Lock button of rear handle
4. Front handle with on/off switch
5. Rear handle with on/off switch
6. Strain relief bracket
7. Blade guard
REMOVE THE BLADE GUARD
Check the cutting attachment. Remove the blade
guard (7) before use and never use blades that are dull,
cracked or damaged. Make sure the machine is in per-
fect working order and all nuts and screws are tight.
OPERATION
PREPARING THE HEDGE TRIMMER
Before starting the hedge trimmer, check that the
trigger switches and safety switches are moving
freely, returning automatically and quickly upon
release. Also check that the cooling air vents are
not obstructed and that both the front and rear
handles are clean and dry.
After making sure that the hedge trimmer isn't
demonstrating any symptoms of damage, you are
ready to begin trimming hedges.
STARTING/STOP THE HEDGE TRIMMER
The hedge trimmer is equipped with a two-hand-
ed safety switch. In order to power the machine
on, you must press both the front handle's safety
24
switch (4) or the rear handle's trigger switch (5)
simultaneously.
Always hold the hedge trimmer with both hands
(B) during operation. Release either the front
handle's (4) safety switch or the rear handle's trig-
ger (5) switch to stop the machine.
TRIMMING (B, E)
1. Cut and remove branches exceeding the cutting
capacity of this product using a proper pruner
before operation.
2. Always hold the product firmly with both hands
on the front handle and rear handle (B). Never
operate this product using only one hand.
3. Do not rush and do not attempt to cut too much
with one stroke of the cutting device.
4. First cut both sides from the bottom cutting up-
wards to the top. This will prevent any of the cut-
tings falling into the path of the area still to be cut.
5. After cutting the sides proceed to the top. Try to
keep the cutting device angled at approximately
15° to the cutting surface (E).
6. When cutting wide hedges with the cutting area
in sight, move the cutting blade lightly through
the cutting surface in a sweeping motion, follow-
ing the shape of the hedge or shrub. A slight tilt
downwards of the cutting blade in the direction
of motion is recommended for optimum cutting
performance.
7. Cut in a number of stages if the area being cut is
particularly long to achieve a better result; small-
er cuttings will allow for easy composting.
8. Lubricate the internal surfaces of the blade if the
English | 11
www.ffgroup-tools.com
Publicité
Table des Matières
