Table des Matières
Publicité
that the steam control switch (C) is in the "0" position.
3.
When the iron reaches the required temperature, the heating indicator light (H) will turn off.
4.
After use, turn the temperature control knob (I) to the "OFF" position.
5.
Remove the plug from the wall socket.
SPRAYING FUNCTION
1.
Fill the water tank with water as described in "Filling with water".
2.
Press water spray button (D).
3.
Note: No matter what steam ironing of dry ironing is, spray will always be available in any case.
STEAM IRONING FUNCTION
1.
Fill the water tank with water as described in "Filling with water".
2.
Plug in. The power/heating indicator lights (M / H) will turn on.
3.
Turn the temperature control knob (I) clockwise to the "MAX" position. Do not turn the switch to" N" or "O" for steam ironing.
4.
When the iron reaches the required temperature, the heating indicator light (H) will turn off.
5.
Adjust the steaming by moving the steam control switch (C).
6.
After use, turn the temperature control knob (I) to the "OFF" position.
7.
Remove the plug from the wall socket.
8.
After each use, make sure that the water tank is empty.
Caution: Do not steam ironing synthetic fabrics, nylon, synthetic silk or silk fabrics. Steam can ruin the texture of the fabric.
BURST OF STEAM FUNCTION
This function will be able to provide more steam to remove stubborn creases.
1.
Set the temperature control knob (I) to MAX until the indicator light (H) goes off.
2.
Release the steam by pressing the steam button (E).
3.
Wait for several minutes and let the steam penetrate through the fabric, and then release more steam through pressing this
button again.
Note:
1. There should be 3-5 seconds rest between two times of pressing Steam burst button (E) in order to obtain the best steaming result.
2. Fill the water to the MAX position before using this function.
3. In order to prevent the water leaking from soleplate, please do not press the steam burst button (E) continuously with more than 5
seconds.
VERTICAL STEAM IRONING FUNCTION
The vertical steam ironing system allows you to use the iron for vertical ironing. This is especially useful for getting wrinkles out of hanging
clothes, curtains.
1.
Fill the water tank with water as described in "Filling with water".
2.
Plug in. The power/heating indicator lights (M/H) will turn on.
3.
Turn the temperature control knob (I) to the "MAX" position. Do not turn the switch to" N" or "O" for steam ironing.
4.
When the iron reaches the required temperature, the heating indicator light (H) will turn off.
5.
Adjust the steaming by moving the steam control switch (C).
6.
Hang the garment on a clothes' hanger and pull the garment tight with one hand.
7.
Hold the iron in vertical position with the other hand and press the steam burst button (E) to iron the garment. Touch the
garment lightly with the soleplate of the iron to remove creases.
8.
After use, turn the temperature control knob (I) switch to the "OFF" position.
9.
Remove the plug from the wall socket.
10.
After each use, make sure that the water tank is empty.
11.
Caution: Do not use steam ironing on clothes or fabrics that are wearing people or animals. The temperature is too high.
SELF-CLEANING SYSTEM
Note: Before you start the self-cleaning procedure, make sure the iron is not plugged in and the steam control (C) is in the "0" position.
1.
Fill the water tank with water up to "MAX". Do not use vinegar or other descaling liquids in the water tank.
2.
Plug in and turn the temperature control knob (I) to the "MAX" position. The power / heating indicator lights (M/H) will turn on.
3.
When the heating indicator light (H) turns off, unplug.
4.
Hold the iron in a horizontal position above the sink. Press and hold the Self-Clean button (J).
5.
Steam and boiling water will start to come out of the iron plate holes, which contain salts and minerals that have been
accumulated in the steam chamber from previous uses.
6.
Gently move the iron back and forth until the water tank is empty.
Caution: The water that comes out during self-cleaning is very hot. Be very careful not to fall on you.
7.
When the water tank is empty, release the self-clean button.
8.
Allow the iron to cool down completely.
9.
Wipe the soleplate with a cold damp cloth.
ANTI-CALC SYSTEM
A special filter inside the water tank softens the water and prevents scale build-up in the soleplate. The filter is permanent and does not
5
Publicité
Table des Matières
