Maintenance And Care; Technical Data - Renkforce BM-88P Notice D'emploi

• Press and hold the ON/OFF button (14) for 7 seconds, until the LED display (12) fl ashes
alternately blue and red.
• When the speaker is found, your Bluetooth® device displays the name "IBlueLife".
• If necessary, enter the password 1234 and couple the two devices.
• After a successful pairing process, the LED display (12) fl ashes blue once every 2 seconds.
Only one Bluetooth® device can be coupled to the speaker at a time. If an active
Bluetooth® coupling already exists, this connection must fi rst be interrupted.
If the speaker or the Bluetooth® device with which there is an active coupling is
switched off or moved out of range, the connection is broken. When the respective
device is turned back on or when the Bluetooth® device comes back into the range
of the speaker, the connection is automatically restored.
To enable this automatic reconnection, this function may need to be activated on the
Bluetooth® device (please inform yourself on this point in the instructions for your
Bluetooth® device).
Audio streaming
Audio streaming is the transmission of audio data (music) via Bluetooth® to the speaker.
If you own an A2DP-capable Bluetooth® device, you can connect it with the speaker via the
pairing procedure as described above and establish an audio transmission.
• Make sure that both devices were connected via pairing.
• Start playback/audio transmission on your Bluetooth® device (see the corresponding operat-
ing manual).
• Now audio transmission is activated.
• You can now control the playback of your Bluetooth® device with the buttons on the control
panel:
- – button (9) decreases the volume
- + button (13) increases the volume
- PLAY/PAUSE button (7) starts or pauses the playback
- REW button (6) jumps back one track
- FF button (11) jumps forward one track
Hands-free mode
The speaker can also be used as a hands-free device for a mobile phone.
• Make sure that both devices were connected via pairing.
• Press the phone button (5) briefl y to accept an incoming call.
• Speak into the microphone (10).
• Press the phone button (5) and hold for about one second to reject an incoming call.
• During a conversation, press the REW button (6) and hold for about one second to put the
call on hold. Press the REW button (6) again and hold for about one second to resume the
call that is on hold.
• Press the FF button (11) and hold for about one second to forward a call to the mobile phone.
• Press the phone button (5) while no call is in progress and hold for about one second to
activate the redial.
• If your mobile phone has a voice-activated dialling function, press the phone button (5) briefl y.
The voice-activated dialling function of the mobile phone is activated. Speak into the micro-
phone (10).
Charging devices through the USB output
Your speaker can also supply power to other devices (e.g. mobile phones, MP3 players, etc.)
that are charged or operated through a USB connection.
In this operating mode, protection against penetrating water is not ensured
because the cover on the back of the device cannot be closed.
The current consumption of the connected device must not exceed 1 A.
The built-in rechargeable battery should be fully charged.
• Open the cover of the connection panel on the back.
• Connect the USB connection of the device to be connected to the USB OUT connection (9).

Maintenance and Care

The device does not need any service, and except for occasional cleaning with a soft cloth, it
does not require any maintenance.
Never use aggressive cleaning agents or chemical solutions as these may damage the surface
of the case.
Disposal
Electronic devices are recyclable waste materials and must not be disposed of in the
household waste!
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.

Technical Data

Charging voltage/power consumption ......... 5 VDC/500 mA
Rechargeable battery .................................. (4.3 V/2300 mAh, Li-Ion battery)
Protection type ............................................. Ipx6
Operation time with one battery charge ....... up to 25 h
Charging time .............................................. approx. 4 hours
Range .......................................................... approx. 10 m
Bluetooth® version ...................................... V2.1 + EDR
Bluetooth® profi le ........................................ A2DP, AVRCP, HSP, HFP
Output power ............................................... 2 x 3 W RMS
Frequency range ......................................... 100-17000 Hz
USB output .................................................. 5 V/1 A
Dimensions .................................................. 204 x 156 x 49 mm
Weight ......................................................... 314 g
All names of companies and products are the trademarks of the respective owners. All rights
reserved.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, or the capture in electro-
nic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment
reserved.
© Copyright 2013 by Conrad Electronic SE.