Maintenance And Cleaning; Technical Data - Renkforce 1230938 Mode D'emploi

Integration of the loudspeaker into the WLAN network
Before you can use the WLAN loudspeaker, it has to be integrated into the existing
WLAN network.
The DHCP function of your network router must be activated (see operating instruc-
tions of your network router).
• Move the MODE SW switch on the rear of the device to the AP position (Access
Point).
• Switch the loudspeaker on using the ON/OFF toggle switch (move switch to ON po-
sition).
• After approx. 30 seconds the colour of the LED on the device's rear panel will chang-
esto a permanent blue-red light.
• Open the WLAN settings of your PC, tablet or smart phone. These settings will dis-
play a new network, called "CT-W1".
To this end, you might have to enable the network search on your PC, tablet
or smart phone.
• Establish a connection with this network.
• Once the connection has been established, enter the address: http://192.168.0.1 in
your web browser.
• Select the button „Connect to Home Gateway" in the menu that opens in the Con-
cert W1.
• Select the tab WIRELESS in the window that opens and check the point CLIENT
under PROFILE.
• Click on the button SITE SURVEY next to SSID.
• A new window opens listing all available WiFi networks. If your WiFi network is not
listed, click on REFRESH to refresh the list.
• Highlight your WiFi network and click SELECT.
• Enter the password for your WiFi network in the field PASSWORD and click APPLY.
• Confirm any messages that might be displayed.
• Switch the WLAN loudspeaker off using the ON/OFF toggle switch (move switch to
OFF position).
• Move the MODE SW switch on the rear of the device to the CLIENT position.
• Switch the loudspeaker on again using the ON/OFF toggle switch (move switch to
ON position).
• The WLAN loudspeaker performs a restart and the colour of the LED on the rear of
the device will change to a permanent blue light after approx. 30 seconds.
Additional information:
• You can find information about the system of the WiFi loudspeaker in the tab STATUS
(SYSTEM INFORMATION).
• In the tab ADMINISTRATOR you can create a password (PASSWORD) for access to
configure the WiFi loudspeaker, to reset it to factory settings (RESTORE FACTORY
DEFAULTS), to restart it (START TO REBOOT) or to perform a firmware update (FIRM-
WARE UPGRADE).
Playback
• After integrating the WLAN loudspeaker into your WLAN network, you can select it
on your DLNA or AirPlay -compatible devices and use it for playback.
®
• Start the playback and select "CT-W1" as the playback source (for this purpose,
please also refer to the operating instructions of the playback device).
To this end, the WLAN loudspeaker has to be registered in the same WLAN
network as your playback device.
Audio playback with cable connection
If your audio device does not have a DLNA or AirPlay
nected to the loudspeaker using the stereo cable provided.
• Connect the LINE IN connector on the rear of the device to the audio output (head-
set output) of your audio device.
• Start playback on your audio device.
• You can now control the playback via the controls of your audio device.
Operation as a power station
The USB output of the WLAN loudspeaker is also able to provide power for other
devices (e.g. mobile phones, MP3 players etc.).
The USB output may be operated with a load of max. 2.5 A. Do not connect
any devices with a higher power consumption.
• Connect the device to be charged to the USB connection at the back of the device.
• Switch the WLAN loudspeaker on using the ON/OFF toggle switch (move switch to
ON position).
• During the charging process, you can insert your mobile device into the base pro-
vided.
function, it can also be con-
®
Maintenance and cleaning
The WLAN loudspeaker is maintenance-free.
Only clean it with a slightly moistened cloth. Never use cleaning agents as these can
damage the surface of the casing.
Should the WLAN loudspeaker not function properly, switch it off and then on again,
using the ON/OFF toggle switch.
If normal operation is still not possible after that, press the RESET button on the back
of the device for approx. 5 seconds using a pointed object (e.g. a straightened paper
clip).
This will reset the device to factory settings, after which it will have to be integrated
into the WLAN network again.
Disposal
Electronic devices are recyclables and must not be disposed of in the
household waste!
Please dispose of the product, when it is no longer of use, in accordance
with the current statutory requirements.
Technical data
Operating voltage............................... 100-240 V/50/60 Hz
Output power ...................................... 2 x 10 W RMS
USB output .......................................... 5 V/DC / 2.5 A
Dimensions.......................................... 395 x 190 x 133 mm
Weight .................................................. approx. 3.3 kg
Declaration of conformity
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, 92240 Hirschau, hereby declare
that this product adheres to the fundamental requirements and the other relevant
regulations of Directive 1999/5/EC.
You can find the Declaration of conformity for this product under
www.conrad.com.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.