Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - HERKULES H-FS 900 Instructions D'origine

6.1.3 Fitting the saw table (Fig. 8, 9)
•
Now mount the wheel guard (3) on the splitter
(19).
•
Turn the knurled screw (9) into the self-
locking nut (18) until the wheel guard can only
just move freely.
•
Move the wheel guard to approximately 5 mm
above the tile you wish to cut and secure it
with the knurled screw (9).
6.2 Changing the diamond cutting wheel
(Fig. 4, 5)
To replace the wheel when worn, proceed as
follows:
•
Pull out the power plug first.
•
Take out the water trough (5).
•
Remove the side cover (17).
•
Apply the counterholder (20) to block the
motor shaft.
•
Use the ring wrench (21) to unscrew the lock
nut (d) on the outer flange (16).
•
Clean the wheel flange thoroughly once the
wheel has been removed.
•
Take out the worn diamond cutting wheel (15)
and fit the new one to the flange, then fit the
outer flange (16) and tighten with the nut (d).
•
Fasten the side cover (17) again.
•
Check that the diamond wheel rotates in the
correct direction!
7. Operation
7.1 Even cutting (Fig. 13)
•
Set the cutting width with the parallel stop (2)
and lock in position with the knurled screws
(10). The width of the workpiece can be read
on the scale.
•
Fig. 13 shows the correct position for your
hands during even cutting. The rate of advan-
ce must not exceed the cutting capacity of the
wheel. This is to make sure that no material
comes off, as this may cause accidents or
injuries.
Notice! Keep a constant check on the water
level
7.2 Making 45° miter cuts (jolly cuts)
(Fig. 14)
•
Position the table as shown in Fig. 14 and
lock in position with the knurled screw (7).
Position the tile with the glazed side on the
work surface and make sure that the diamond
Anl_H_FS_900_SPK7_fürCumulus_komplett.indb 18 Anl_H_FS_900_SPK7_fürCumulus_komplett.indb 18
GB
wheel does not touch the glaze on the tile.
Correct the cutting guiding position if neces-
sary.
•
Fig. 14 shows the correct position for your
hands during miter cutting to 45°. The right
hand holds the workpiece in contact with the
diamond wheel while the left hand pushes the
workpiece forward. The rate of advance must
not exceed the cutting capacity of the wheel.
This is to make sure that no material comes
off, as this may cause accidents or injuries.
7.3 On/Off switch (Fig. 1)
•
To switch on, press the „I" on the On/Off
switch (12).
•
To switch off, press the „0" on the On/Off
switch (12).

8. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
9. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
9.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
- 18 -
02.04.2020 07:49:03 02.04.2020 07:49:03