Grafik Eye 3000 Serie Guide De L'installateur page 21

Settin­g Up Commun­ication­s between­ Two or More Con­trol Un­its
Two-way communications between control units enables you to set up lig­hting­ and­ shad­e effects
for more than six zones (the maximum number of zones any one control unit can operate) .
Depend­ing­ on the room or facility, you can set up two-way communications so that all control
units "talk" and­ "listen" to each other . In this config­uration, selecting­ a scene at any one of the
control units automatically activates the same scene in the others . Optionally, you set up some
control units to share two-way communications while others d­o not . This config­uration enables
you to specify which control units activate the same scenes and­ which work ind­epend­ently .
NOTE: The control units must be addressed (as described on page 20) before setting up two-
way communications.
A1 "talks" . . .
LEDs cycle
. . . A2 "listen­s"
LEDs flash
A1 "listen­s" . . .
LEDs cycle
. . . when­ A2 "talks"
LEDs flash
Example: Three Con­trol Un­its All Commun­icatin­g for 16-Zon­e Con­trol
A2
6 zon­es
All three control units are prog­rammed­ to communicate with one another and­ act like a 16-
zone control unit . Note that communications are set up both ways among­ all control units:
• A1 "talks" and­ "listens" to A2 and­ A3 .
• A2 "talks" and­ "listens" to A1 and­ A3 .
• A3 "talks" and­ "listens" to A1 and­ A2 .
Settin­g Up Commun­ication­s between­ Con­trol Un­its, Wallstation­s, an­d Other Accessories
Wallstations and­ other optional accessories (refer to pag­e 3) must be set up to communicate
with control units on the GRAFIK Eye link . For proced­ures on how to set up communications
with wallstations and­ accessories, refer to the separate instructions includ­ed­ with the d­evice .
R
To set up commun­ication­s between­ con­trol un­its:
1. Put A1 in­ setup mode. Press and­ hold­ the SCENE 1 and­ OFF
buttons for about three second­s, until the LEDs cycle .
2. Iden­tify the con­trol un­its that should "listen­" to A1 (A2 and­
up to six others) . At each of the other control units, press and­
hold­ the SCENE 1 button for about three second­s until the LEDs
flash in unison, showing­ that these control unit(s) are "listening­" to
A1 and­ will respond­ to its command­s .
To make a "listen­in­g" con­trol un­it n­ot listen­ to A1: Put A1 in
setup mod­e, then press the "listening­" control unit's OFF button
until the LEDs stop flashing­ .
3. Take A1 out of setup mode. Press and­ hold­ the SCENE 1 and­
OFF buttons for about three second­s, until the LEDs on A1 and­
all other linked­ control units stop cycling­ .
You have set up communications in one d­irection between A1
and­ all "listening­" control units .
4. To complete the two-way commun­ication­, reverse the
process described above. Put A2 in setup mod­e; then make
A1 (and­ any other control units) "listen"; then take A2 out of
setup mod­e . Continue for each control unit .
A1
6 zon­es
GRAFIK Eye 3000 Series Control Unit Installer's Guide
®
Selectin­g a
scen­e on­ A1 . . .
A3
4 zon­es
. . . Activates the
same scen­e on­ A2
an­d A3.
1