Description; Installation; Removing Module From Carton; Operation - Philips AutoDome LTC 0809 Serie Manuel D'utilisation

4

INSTALLATION

Attention: Installation should be performed by
qualified service personnel only in accordance with
the National Electrical Code or applicable local
codes.
4.1

Removing Module From Carton

Refer to ILLUSTRATIONS for component description.
CAUTION: Keep in carton until ready to install
in backbox. Be sure to observe all safety measures
for static control when working with this unit
while out of its enclosure. Otherwise, static
damage may result.
For removal from carton and installation instructions, see
LTC 0809 Series Camera Module Installation under
INSTALLATION in the Instructions for Use supplied with
the applicable LTC 7460 Series Ceiling Mount ordered.
CAUTION: Do not handle the unit by the circuit
board because this may result in physical damage
to the unit.
5

OPERATION

5.1

Camera Control

These units, as shipped, are factory adjusted as described below:
• Line-lock mode enabled with zero degree phase delay.
• AGC on.
• Backlight compensation off.
• Electronic shutter off.
• Automatic white balance on.
5.2

Changing Operating Modes

The AutoDome unit operating modes can be changed using
either a TC8135B Series Controller/Follower or an Allegiant ®
series keyboard. An Allegiant series keyboard is required to take
full advantage of all the various features available. See
AutoDome Commands for description of various operating
adjustments.
5.3

AutoDome Commands

PAN & TILT - COMMANDS USING AUXILIARY CONTROLS
Receiver/Driver Aux
Function No.
Scan 1
Auto-Pan 2
Pre-Position 8
Tour
Return Home 9
Set Scan/auto-
pan speed 14
Set tour period 15
Auto-Speed 16
Auto-Pivot 18
Enable
Field of View 45
Optimize
LENS - COMMANDS USING AUXILIARY CONTROLS
Lens Function Aux No. Description
Iris Control 3
Focus Control 4
Auto-iris ALC adj 10
Auto-iris Level adj 11
Auto-focus 12
Activation
Auto-iris Activation 13
Spot Focus 17
CAMERA - COMMANDS USING AUXILIARY CONTROLS
Camera Aux No.
Function
Backlight 20
Compensation
Shutter 23
Auto shutter 24
activation
White Balance 30
Red Adjust 31
Blue Adjust 32
R-Y Hue Adjust 33
B-Y Hue Adjust 34
Fixed White 35
Balance
Factory Default 40
Settings
Adjust LL Phase 41
Delay
Sync Mode 42
AGC 43
Vertical Aperture
Adjust 44
1.2

Description

On/Off
Auto-pan without On/off
limits
Auto-pan between On/off
limits
-- On/off
return to home On/off
upon inactivity
-- Inc/dec
Sets pause Inc/dec
between tour
callups
Enables/disables On/off
auto-speed
Enables/disables On/off
auto-pivot
--- On/off
On/Off
-- Auto/
manual
-- Auto/
manual
-- Peak/ave 1, 7
-- Inc/dec
Activates AF On/off
upon movement
Activates AI On/off
upon movement
Activates Spot On/off
On/Off
On/off
On/off
On/off
Auto/
manual
Inc/dec
Inc/dec
Inc/dec
Inc/dec
Indoor/
outdoor
Set/---
Inc/dec
ll/xtal
On/off
Inc/dec
Notes
5, 8
8
8
2, 7
2, 7
2, 7
2, 7
2, 7
2, 7
Notes
1, 9
1, 9
1, 7
2
2
2, 7
Notes
1, 10
1, 7
2, 7
7
1, 7
1, 7
3, 7
3, 7
1, 7
1,3, 7
3, 7
3, 7
3
7