Functional Description - Milwaukee 6034-21 Manuel De L'utilisateur

SYMBOLOGY
Double Insulated
Volts
Alternating Current
Alternating Current/Direct Current
Amps
OPM
Orbits Per Minute (OPM)
UL Listing for Canada and U.S.
C US

FUNCTIONAL DESCRIPTION

1
2
3
1. Gripping surface
2. On/Off switch
3. Speed dial
4. Backing pad
5. Dust box with filter
6. Universal hose adapter
ASSEMBLY
To reduce the risk of injury, always
WARNING
unplug tool before changing or
removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Selecting Sandpaper and Grits
Sandpaper can be made from various grit materials
and these should be selected according the material
to be sanded. The guidelines below list materials
and grit materials that should be used with them.
•Fine woodwork – garnet or aluminum oxide
•Rough woodwork – aluminum zirconia or ceramic
aluminum oxide
•Manufactured wood products (particleboard,
medium density fiber board etc.) – silicon carbide
or aluminum oxide
•Solid surfacing materials (Corian, etc.) – silicon
carbide or aluminum oxide
•Metals – emery or aluminum oxide
Sandpaper is also graded by coarseness. Start
your work with an abrasive grit just coarse enough
to remove high spots and excessive roughness.
Follow with a second sanding using a grit one or
two grades finer. Continue with successively finer
grits until you obtain the desired finish.
5
6
4
4
Do not switch from a coarse grit to a very fine grit in
one step because it may be difficult to remove the
marks made by the coarse grit abrasive. Use the
finest grits practical for the roughing operation, and
finish by using successively finer grits.
Grit Type
Ideal for initial sanding on
rougher surfaces. For fast stock
60
Coarse removal. Rough sanding and
80
stripping of painted and rusted
surfaces.
For intermediate sanding and
100
Medium removal of minor surface im-
120
perfections.
150
Ideal for fine sanding prior to
180 Fine
straining, priming, or sealing.
220
Attaching Hook-and-Loop Sanding Discs
1. Unplug the sander.
2. Align holes in hook-and-loop type sanding disc
with holes in pad, then carefully press fuzzy side
of sanding disc against pad as tightly as possible.
NOTE: Hook-and-loop type sanding discs can
be reused for the life of the sanding abrasive. It
is recommended that you keep the sanding disc
backing pad clean to provide for best adhesion.
Clean occasionally by brushing lightly with a small
brush.
Changing the Sanding Pad
The sander comes assembled with the hook-and-
loop pad. To attach a pressure sensitive adhesive
(PSA) pad (not included), first remove the hook-and-
loop pad. Inspect sanding disc before installing. Do
not use if broken or defective.
1. Unplug the sander.
2. Remove the four screws that
hold the hook-and-loop pad
in place.
3. Remove the hook-and-loop
pad.
4. Clean dust particles from
the pad brake.
5. Apply a thin layer of light-
weight grease to the back
of the pad.
6. Align the holes in the pres-
sure sensitive adhesive
(PSA) pad with the four
screw holes in the sander.
7. Replace the four screws securely.
Attaching PSA Sanding Discs
1. Unplug the sander.
2. Carefully peel paper backing from the pressure
sensitive adhesive type sanding disc.
3. Align holes in sanding disc with holes in backing
pad, then carefully press sticky side of disc against
pad as tightly as possible.
NOTE: Holes in sanding disc must line up with
holes in the backing pad in order for the dustless
feature of the sander to function properly.
NOTE: It is recommended that you clean backing
pad occasionally by brushing lightly with a small
brush. Dust buildup on backing pad could cause
sanding disc not to stick properly.
Typical Application