Additional Safety Rules - Makita 2414NB Manuel D'instructions

ENGLISH
1 Safety guide
2 Shaft lock
3 Socket wrench
4 Cut-off wheel
5 Inner flange
6 O-ring
7 Spindle
8 Ring
9 Outer flange
10 Hex bolt
11 Screw
12 Spark guard
SPECIFICATIONS
Model
Wheel diameter .................................................................................................................................................. 355 mm
Hole diameter .................................................................................................................................................... 25.4 mm
–1
No load speed (min ) ............................................................................................................................................ 3,800
Dimensions (L x W x H)
With under cover..............................................................................................................500 mm x 280 mm x 620 mm
Net weight
For tools with European type safety guide and under cover.............................................................................. 18.5 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for cutting in masonry and ferrous
materials with appropriate abrasive cut-off wheel.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.26 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
Explanation of general view
13 Guide plate
14 Hex bolts
15 Vise plate
16 Vise nut
17 Vise handle
18 Spacer block
19 Straight piece of wood
(Spacer)
20 Over 190 mm long
21 Over 45 mm wide
22 Over 65 mm wide
23 Diameter of workpiece

ADDITIONAL SAFETY RULES

1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Make sure the wheel is not contacting the work-
11. Before using the tool on an actual workpiece, let
12. Watch out for flying sparks when operating.
13. Remove material or debris from the area that
14. Use the cutting edge of the wheel only. Never
15. If the wheel stops during the operation, makes
24 Spacer block
25 Vise
26 Width of spacer block
27 Blocks
28 Switch trigger
29 Lock button/Lock-off button
30 Wing bolt
31 Under cover
32 Limit mark
33 Screwdriver
34 Brush holder cap
Wear protective glasses. Also wear hearing pro-
tection during extended periods of operation.
Use only wheels recommended by the manufac-
turer which have a maximum operating speed at
least as high as "No Load RPM" marked on the
tool's nameplate. Use only fiberglass-reinforced
cut-off wheels.
Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
Secure the wheel carefully.
Use only flanges specified for this tool.
Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt, or the
wheel itself might break.
Keep guards in place and in working order.
Hold the handle firmly.
Keep hands away from rotating parts.
piece before the switch is turned on.
it simply run for several minutes first. Watch for
flutter or excessive vibration that might be
caused by poor installation or a poorly balanced
wheel.
They can cause injury or ignite combustible
materials.
might be ignited by sparks. Be sure that others
are not in the path of the sparks. Keep a proper,
charged fire extinguisher closely available.
use side surface.
an odd noise or begins to vibrate, switch off the
tool immediately.
2414NB
ENB066-1
5