Publicité
Les langues disponibles
Les langues disponibles
Pressing B at the UPLOAD ALL
mode will go to the UPLOAD
RACE mode with display as
shown in Fig.23.
Pressing A in this mode will only
upload the memories in this
race. Press B to
select
particular
race
upload. Pressing C any time
during
this uploading process
will stop uploading immediately.
** If the chronograph is not
reset
(i.e.
still
running
stopped), it will not be possible
to upload and the display will
show UPLOAD 0, there will not
be any action upon pressing A or
B.
** If the printer is wrongly
turned on during the UPLOAD
process, NO or irrelevant data
will be uploaded to the PC.
TIME
Press C to go to the TIME mode.
The display is as shown in
Fig.24.
Press and hold B button for 2
seconds will go into the TIME
SET mode with the AL HOUR
blinking. Press A to set the AL
HOUR. Press B to select digits
in the following sequence: AL
HR, AL MIN first digit, AL MIN
2nd digit, AL OFF/ON, YEAR
last
digit,
YEAR
1st
MONTH,
DATE,
12/24HR
selection, HOUR, MIN
1st digit, MIN 2nd digit and
SECONDS.
Press A to set the
blinking digits. Pressing C any
time during this setting sequence
will
complete
the
setting
procedure and return to the
normal TIME display as shown in
Fig.24.
If 12HR option is selected the
calendar
will
MONTH/DATE/YEAR and time
will be displayed in 12 HOUR
system.
If 24HR option is
selected, the calendar will be
displayedas
DATE/MONTH/YEAR and time
will be displayed in
24 HOUR system.
to
The
calendar
adjusts for weekday and odd
and
even
February of leap years up to year
2089.
or
Press D in the TIME mode to arm
or disarm the alarm. When the
alarm
is
armed
indicator will be turned on and
the alarm will sound at the preset
alarm time.
BATTERY LOW INDICATION
When the battery low indicator
lights up, as shown in Fig. 25,
battery replacement is
necessary.
**: Only replace the CR2032
with the 4 pieces AA size
alkaline batteries installed.
This can retain the stopwatch's
memories and settings.
LOADING OF PAPER
1. Use thermal paper roll size:
Width 37mm x Diameter 30mm
max.
2. Pull out the paper cover by
pressing both side of the cover
slightly, as shown in Fig. 26.
3. To ensure smooth insertion,
cut the corner of the thermal
paper as shown in Fig 27.
digit,
4. Switch on the printer by sliding
up the ' PRINT ON / OFF ' switch.
5. Insert the end portion of the
paper into the paper insertion
slot, as shown in Fig. 28.
6. Press the ' PAPER FEED
SWITCH '(Fig. 29) until the end
of paper is about 1 cm out from
the paper cutter.
7. Replace the paper cover to its
be
shown
as
automatically
months including
the
alarm
**: Do not pull paper out from
the printer, this will cause
damage to the printer. For
replacing the paper roll
before it is used up, tear the
paper off and press the
' PAPER FEED SWITCH ' until
the remaining paper is out
completely.
**: Do not touch the surface
of the paper as it may cause
poor printing.
**: Always store the paper
rolls in a cool, dry place and
keep away from direct
sunlight.
OPTIONAL
ACCESSARY(FOR UPLOAD):
To upload data to computer, the
computer must have the '
DigiLink Upload Software '
installed (please see DigiLink
upload program).
Follow the steps below to
connect the computer and the
stopwatch:
1. Shut down the computer.
2. Plug the USB upload cable
into the USB socket of the
computer.
3. Insert the telephone-plug end
of the connector cable into the
right hand side of the stopwatch
labeled ' PC ' (Fig. 30)
4. Plug the jack end of the
connector cable into the socket of
the upload cable completely (Fig.
31).
original position.
Fig. 26
Paper Feed switch
Fig. 28
Fig. 29
Fig. 27
Publicité
