Publicité
Les langues disponibles
Les langues disponibles
is set to 180 and time unit to
seconds, the speed reading for 3
strokes gives the number of
strokes / minute.
** MEMORY USED UP-- When all
the memories have been used the
4 digit LAP counter at the top left
corner will start blinking to indicate
all memories have been used up.
All further LAP memories will not
be recorded in the memory unless
some memories are cleared as
previously indicated. When there
is no memory left pressing A to
start a race will sound 3 short
beeps.
** Do not leave the stopwatch
running if not in use as that
drains a higher power from the
battery.
TIMER OPERATION
Press
C
button
until
stopwatch goes to the TIMER
mode. The display is as shown in
Fig.18. The top row is the display
for the 1st timer and the middle
row is the display for the 2nd
timer.
Press and hold B button for 2
seconds will go into the SET
TIMER mode with the hour digit
of the 1st timer blinking. Press A
button to set to desired hour for
countdown. Press B to go to the
first digit in minutes and press A
to set minutes. Similarly by using
B and A buttons the desired
countdown times for the 1st and
2nd timers can be set.
**Pressing C button once any
time during this TIMER setting
sequence will complete the
setting and the timer is ready to
start upon pressing the A button.
Press A to start countdown with
the "1" at the top right corner
blinking and the timer setting
counting down. When the 1st
timer approaches zero, the timer
gives 4 beeps and the 2nd timer
starts counting down
immediately. When the
2nd timer approaches zero, it
gives 2 beeps and the 4 digit
counter at the lowest row
advances by 1 automatically. At
any time during countdown
pressing A will stop counting.
** If only the 1st timer is set the
timer is used as an ordinary
countdown timer and will give 5
times 4 beeps when the set time
is up. The 4 digit counter also
advances by 1 automatically
the
when the timer reaches zero.
PRINT MODE
Press C button to go to the
PRINT ALL mode as shown in
Fig.20. Pressing A button will
print all recorded memories
(when the printer is on). When
the stopwatch is in the process of
printing, an indicator moves from
Fig. 17
right to left. When printing is
complete PRINT END is
Fig. 18
displayed.
Pressing B at the PRINT ALL
mode will go to the PRINT RACE
mode with display as shown in
Fig.21.
Pressing A in this mode will
only print the memories in this
race. Press B to select particular
race to print. Pressing C any time
Fig. 19
during this printing process will
stop printing immediately.
**
Slide
SWITCH to the TOP position.
Only
the
(depending
Fig. 21
the
PRINT
MODE
SPLIT
or
SPEED
on
whether
the
stopwatch is in CHRONO or
SPEED mode) will be printed. If
this switch is slide to the DOWN
position, both LAP and SPLIT or
LAP and SPEED will be printed.
(In SPEED mode, if B is pressed
while the previous record is still
being printed, that SPEED record
cannot be printed in real time.
The memories still record the full
data for recall or upload).
** If the chronograph is not
reset
(i.e.
still
running
stopped), it will not be possible
to print and the display will show
PRINT 0, there will not be any
action upon pressing A or B.
** Do not leave the printer on if
not in use as that drains a higher
power from the battery.
** If the above process is
wrongly
done
with
display switched to
UPLOAD ALL, the display will
be freezed until the printer is
switched off.
UPLOAD MODE
The PRINTER must be switched
OFF in UPLOAD MODE.
In Fig. 20 press D button once
will switch to UPLOAD ALL
mode
as
shown
in
Pressing A button will UPLOAD
ALL
recorded
memories
computer
(if
computer
connected). When the stopwatch
is in the process of uploading, an
indicator moves from right to left.
When
upload
is
complete
UPLOAD
END
is
displayed.
Press D button to return to
PRINT MODE.
or
the
Fig.22.
to
is
Publicité
