Valex LR 39 Instructions Pour L'installation page 10

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

g
I mportant! The chain saw must be used by operators trained to
cut trees.
WARNING! Before using this tool, carefully read and follow the
instructions in this manual that refer to the diagrams and techni-
cal data contained in the enclosed sheet in order to ensure that
commissioning, starting, use, stopping, and maintenance are
carried out properly.
WARNING! Before using the tool, in order to ensure that correct
commissioning, start-up, use, stopping and maintenance are
carried out correctly, please read carefully and apply the following
instructions. Before beginning work, you should be familiar with
the controls and safe use of this tool. Make sure you know how to
stop it in case of an emergency. Incorrect use of this tool could
result in serious injury or death and damage to property. Always
consider your safety and the safety of others and act accordingly.
N.B.: this tool is made only to cut wood and must not be used on
other materials.
Any use of this tool other than those indicated in these instructions
may damage the tool and create serious risk to both people and
property.
WARNING! The engine works exclusively with an oil-petrol mixture
in the percentage indicated. If this mixture is not used, irrepara-
ble damage will be caused to the engine with immediate loss of
warranty.
Please keep these instructions and the attached sheet in a safe
place and have them available for further reference if needed.
MACHINE DESCRIPTION (FIG. A)
1. Exhaust
2. Rear handgrip
3. Chainstay
4. Accelerator lever
5. Accelerator lever release button
6. Oil tank cap
7. Front hand grip
8. Front hand guard/ emergency chain brake lever
9. Start handle
10. Bar
11. Bar cover
12. Chain
14. Fuel tank cap
15. Chain tensioning screw
16. Bar fixing pin(s)
17. Bar fixing nut(s)
18. Housing
19. Sprocket
20. Chain tension pin
21. Bar groove
22. Bar lower hole
23. Oil hole
24. Air control lever
25. Engine off switch
26. Brake clutch unit
27. Internal combustion engine
28. Open cover lever.
29. Spacer for packaging
30. Spark plug
31. Air filter
32. Fuel priming pump
35. Carburetor Adjustments
36. Adjustment screw for chain lubrication oil
- 10 -
DESCRIPTION OF MARKS AND SYMBOLS (FIG. B)
1. Machine name
2. Technical data
3. Marks
4. Manufacturing batch number. The first 2 figures of the batch
indicate the year of manufacture.
5. Engine approval data
6. Mixture oil-petrol
7. Oil chain
8. Emergency Stop
9. Air valve in the carburetor
10. Adjust oil flow on chain
STARTING UP
WARNING! Always use protective gloves when handling the chain.
WARNING! Before carrying out any work on the tool, switch off the
internal combustion engine.
BAR AND CHAIN
1 Assembly of the bar, the chain, and the housing (Fig. A)
- Put the chain (12) in lubricating oil and leave there for some hours.
- Check that the emergency brake is released by pulling the hand
guard (no. 8) toward the front handle.
- Place the chain saw on a flat surface and remove the nut/s ( 17) and
the housing (18). Also remove the plastic spacer (29), if present,
inserted in the fixing pin. This spacer (Fig.F) must not be used!
- Using a screwdriver, turn the chain adjustment screw counter-
clockwise (15) until the end of the screw.
- Slip the bar groove (21) over the fixing pin/s (16) and pass the chain
over the sprocket (19). During this phase it is important to centre
the tensioning pin (20) on the lower hole of the bar (22).
- Insert the chain in the bar grooves making sure to respect the correct
direction of the chain (Fig. E).
- Assemble the housing (18) and, holding the nose of the bar upwards
(using gloves!), fix the nut/s (17) tightly.
WARNING! Do not use the chain saw before tensioning the chain.
2 Tensioning the chain (Fig. A)
- Loosen the bar fixing nut half a turn (17).
- Using a screwdriver, turn the chain adjustment screw clockwise
(15) until the chain has reached the correct tension.
N.B.: Checking the correct tension. The correct tension is reached
when you are able to manually lift the chain 3-4 mm to the centre
of the bar (Fig.C).
- If the chain is too tense, loosen the nut/s (17) and the chain
adjustment screw (15) and push the bar leftwards in such a way
as to make it slip into place.
- Repeat the adjustment taking care to tighten the screws less (15).
- When the chain has been adjusted, fix the nut/s (17) securely, always
holding the nose of the bar upwards.
- Check for the correct tension again.
- Lubricate the chain and bar rail with specific oil.
WARNING! During the first cuts, when the machine is still new,
the chain will loosen quite frequently, but this is normal during the
breaking-in period of a new tool.
WARNING! Never leave the chain loose as it may come off the
bar while cutting.
WARNING! If the chain is too tight, it could cause overheating and
damages. It is forbidden to use the machine without lubricating
oil for the chain.
OPENING THE GUARD
Follow the instructions below to remove the guard correctly (no. 18):
1 – Pull the hand guard no. 8 towards the hand grip
2 - Remove the bar fixing nuts no. 17.
3 – Loosen (unscrew) the chain tensioning screw no. 15
4 – Extract the guard.

Publicité

Table des Matières
loading

Produits Connexes pour Valex LR 39

Table des Matières