Technical Data; Attachment And Operation - Scheppach LBH3800E Traduction Du Manuel D'origine

– Avoid abnormal working postures. Make sure you
stand squarely and keep your balance at all times.
In this way, you can control the electric tool better in
unexpected circumstances.
– Wear suitable work clothes. Do not wear loose clothing
or jewellery. Keep hair, clothes and gloves away from
moving parts. Loose clothing, jewellery or long hair
can get trapped in moving parts.
– If vacuuming devices and draining devices can be fit-
ted, make sure that these are correctly attached and
correctly used. The use of a dust extraction system
can reduce the danger posed by dust.
4 Usage and treatment of the electric tool
– Do not overload the appliance. Use the correct tool for
your work. You will be able to work better and more
safely within the given performance boundaries.
– Do not use an electric tool with a defective switch.
An electric tool that cannot be switched on or off is
dangerous and must be repaired.
– Pull the plug out of the socket and/or remove the bat-
tery before making any adjustments to the appliance,
changing accessories or put the appliance down. This
safety measure prevents starting the electric tool un-
intentionally.
– Keep unused electric tools out of the reach of child-
ren. Do not allow people who are not familiar with the
appliance or who have not read these instructions to
use the appliance. Electric tools are dangerous if they
are used by inexperienced people.
– Clean your electric tool carefully. Check whether mo-
ving parts are functioning properly and not jamming,
whether parts are broken or damaged enough that
the functioning of this electric tool is affected. Have
damaged parts repaired before using the appliance.
Many accidents are caused by badly maintained elec-
tric tools.
– Keep your cutting tools sharp and clean. Carefully
maintained cutting tools with sharp cutting edges will
jam less and are easier to control.
– Make sure to use electric tools, accessories, attach-
ments, etc. in accordance with these instructions. Take
the conditions in your work area and the job in hand
into account. Using electric tools for any purpose other
than the one for which they are intended can lead to
dangerous situations.
Residual risks
The machine has been built using modern technology
and in accordance with recognized safety rules.
Some hazards, however, may still remain.
• Risk of injury to fingers and hands from the tool in ope-
ration during improper use.
• Electrical hazards when unsuitable electric connec-
tions are used.
• Safety hazard from the electric tool in case of long hair
and loose clothing; Wear personal protective equip-
ment such as a hair net and tight work clothing.
• Although having regarded all considerable rules there
may still remain not obvious remaining hazrds.
20 GB
• Minimize remaining hazards by following the instruc-
tions in "Safety Rules", "Use only as authorized" and
in the entire operating manual.

6. Technical data

LBH3800E
Technical data
Dimension LxWxH mm
Air speed min./max.
km/h
air volume min./max.
m /min
3
Wheel diameter mm
dust bag capacity l
Power unit
Engine V / Hz
Motor speed max. in
rpm
Engine output W
Weight kg
Subject to technical changes!
concerning noise
Information
according to relevant standards:
Sound pressure L = 86.6 dB(A)
pA
Sound power L = 100 dB(A)
WA
Uncertainty K = 2 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A = 0.82 m/s
2
hv
Uncertainty K = 1.5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the places
that have to do with your safety with this sign: m

7. Attachment and operation

ATTENTION! Before working on the device ­ cleaning, in­
spection, maintenance or other work ­ always turn off the
device and separate it from the power supply.
ASSEMBLY
m The Vac-blower must not be used or switched
on until it has been fully assembled.
Height adjustment (Fig. 2 + 3)
• Press the button (2.1) and slide the air duct (5). It
can be adjusted up to 300mm.
770x160x1110
165 / 275
10 / 13.5
70
45
230 / 50
14000
2800
3.2
emission measured