Zelmer SYRIUS Mode D'emploi page 17

1 To replace the HEPA H11 filter lift the vacuum cleaner
handle and open the accessory compartment.
2 Grab the outlet filter cover (7) by the two fastenings,
press firmly with the thumbs and pull it to the outside.
3 Remove the HEPA H11 filter case and replace it with
a new one. The HEPA H11 filter ensures an effective
operation of the vacuum cleaner for about 1 year.
4 Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
●
Close accessory storage.
SAFBAG dust bag disassembly/assembly
1 The vacuum cleaner is equipped with a safety valve
which is located in the dust container (bag) chamber.
It opens automatically when the suction hose or the elements
attached to the suction hose are completely clogged or when
the dust bag is overfilled with dust. After the opening of the
valve a characteristic "fluttering" in the vacuum cleaner will
be heard. The opening of the safety valve will result in the
lighting of the dust bag full indicator.
2 When the dust bag full indicator (12) lights (with the
nozzle or the brush lifted above the cleaned surface) it means
that the bag is full and needs to be replaced. In addition the
dust bag full indicator may activate if the suction hose or the
elements attached to the suction hose are clogged.
3 Switch off the vacuum cleaner by pressing the "on/off"
button (1) and unplug the appliance.
4 Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
5 Release the front cover fastening (13) and open the cover.
6 While holding the dust bag plate, gently bend it towards
the inside of the dust container chamber and remove the
whole dust bag upwards.
7 Insert the plate of the new dust bag in the tracks and
slide the plate together with the screen to the bottom of the
container, unfold the dust bag. The direction for inserting the
dust bag is indicated by the arrow on the bag.
8 Close the cover by pressing it until you hear
a characteristic click – pay attention not to trap the dust bag.
It is recommended to replace the dust bag if:
a) the dust bag full indicator lights up,
b) the safety valve activates,
c) the vacuum cleaner operates poorly,
d) the dust bag is full.
End of operation cleaning and
maintenance
1 Switch off the vacuum cleaner by pressing the "on/off"
button (1).
2 Unplug the appliance.
1600-018_v01
3 Wind the cord by pressing the cord rewind button (3).
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4 Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
5 Disconnect the telescopic tube from the nozzle or brush.
6 Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the "A" locking
device and pull the tube in the direction of the arrow.
7 The vacuum cleaner may be stored horizontally. The hose
may be attached to the vacuum cleaner, however you have to
make sure that it is not excessively bent during storing.
E
8 If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
Examples of problems while operating the
vacuum cleaner
PROBLEM
A characteristic "fluttering"
of the vacuum cleaner is
heard which indicates the
opening of the safety
valve.
The dust bag is damaged. Remove the dust bag and the filters.
The suction power of the
vacuum cleaner is weak.
The electrical installation
fuse went out.
The vacuum cleaner
does not operate; the
housing or the cord is
damaged.
F
ACTION
• The dust bag may be full – replace
the dust bag.
• Replace the dust bag even if it is not
full yet. In unfavorable conditions, fine
dust might have clogged the pores on
the surface of the dust bag.
• The suction tube, the hose or the
attachment is blocked – remove the
cause of the clogging.
Replace the dust bag and the filters,
check the suction tube, the hose and
the nozzle - remove the cause of the
clogging.
Check if other appliances are not
plugged to the same electrical circuit
as the vacuum cleaner. If the fuse
goes out repeatedly, return the vacuum
cleaner to a service point.
Return the vacuum cleaner to a service
point.
17