Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
This beer dispensing unit will support one half (
or one quarter (
⁄
) barrel. The double draft tower units can
1
4
support two sixth (
⁄
) barrels of beer. See chart below for
1
6
quantity of beer in each barrel size.
1/6 barrel
23
⁄
5
16
Height
(59.2 cm)
9
⁄
"
1
4
Diameter
(23.5 cm)
Gallons
5.23
# 1 2 o z .
53
Glasses
Keg Size
5 gallon Corny
1/6 barrel
1/4 Barrel
1/2 Barrel
Tap Equipment and Assembly
Your dispensing kit includes the following parts:
Polished stainless steel tower with clear beer line (single
or double dispense)
Tower Gasket
Phillips oval head screws
Knob for Tower (Faucet Handle)
Keg coupler(s)
90° Elbow fitting(s)
Black Rubber Washer(s)
CO
regulator with red gas line(s) attached
2
Empty 5 pound CO
tank
2
Plastic clamp(s)
Faucet wrench
1
⁄
3
8
(35mm)
Typical
2
⁄
3
4
(70mm)
Typical
USING YOUR REFRIGERATOR
1
Barrel Sizes
1/4 Barrel
1/2 Barrel
"
14
⁄
"
13
16
(37.6 cm)
(59.2 cm)
17"
17" to 17
(43.2 to 43.cm)
(43.2 cm)
7.75
82
Table A
#of kegs per
5 pound CO
Tank
2
15 to 22
14 to 21
10 to 14
5 to 7
Table B
11" to 12"
(27.9cm to 30.5cm)
25" (63.5cm)
Diameter
to suit
1
⁄
(38mm) Diameter
1
2
Figure 10
⁄
) barrel
Tools required for installation:
2
Phillips screwdriver
Pliers
Adjustable wrench or a 1
23
⁄
"
5
16
CO
can be dangerous. If it becomes difficult to
2
breathe and/or your head starts to ache, a high
⁄
"
1
4
concentration of carbon dioxide may be present.
Leave the area immediately.
15.5
•
The CO
regulator. Never connect the tank to the keg.
163
•
The CO
upright position. Secure it with the chain pro-
vided.
•
Never drop or throw the CO
•
Keep the CO
•
Ventilate the area after a CO
Assembly procedure:
1. Remove shelving and packaged components from the
interior of the refrigerator before beginning the assem-
bly process.
2. Take your empty 5 pound CO
supply dealer to be filled. You can usually find them in
your "yellow pages" under "Welding Supply" or "Fire
Protection". One 5 pound tank can process many kegs
(see table B) Your dealer should supply you with a
plastic washer every time the tank is filled.
3. Tower mounting (if you are installing the unit under a
counter skip to step 3). If you are mounting the tower
directly to the top of the refrigerator, first remove the
four screws from the top of the refrigerator. Feed the
clear beer line through the tower gasket and the large
hole in the refrigerator top. Align the 4 holes in the
tower with the 4 holes in the refrigerator top and secure
the tower with the 4 screws removed previously. Skip to
step 4.
4. If you are installing your keg refrigerator under a
counter you will need to drill 5 holes in the counter top
to mount the tower. The first hole is a 1
hole located at the center of the tower for the beer line,
locate approximately 11 to 12 inches from the back wall
(based on a standard counter top depth of 25"). Next
drill the 4 tower mounting holes per the dimensions
in Figure 10. The hole diameter is dependent on the
counter top material and if screw anchors are required.
The screws supplied are in the literature pack and are
a #10 x 1" type AB stainless steel screw. After the holes
are drilled and the keg refrigerator is in place under the
counter top feed the beer line through the tower gasket,
7
⁄
" open end wrench
1
8
tank must always be connected to the
2
tank must be securely mounted in the
2
tank.
2
tank away from heat.
2
leak.
2
tank to your local gas
2
⁄
" diameter
1
2
Publicité
Chapitres
Table des Matières
