Dremel 3D45 Consignes D'utilisation/De Sécurité page 4

DM 2610047405AB 03-18_3D45 3/27/18 9:51 AM Page 4
4
Ensure small objects created by Dremel
3D45 are not accessible to young children.
Small objects are potential choking hazards for
young children.
Do not create illegal or inappropriate objects
using Dremel 3D45.
Do not use Dremel 3D45 to create objects
intended for use with candles, liquid fuels,
and other heat sources. Plastic may melt
when exposed to fire or other heat sources.
Such use of objects created by Dremel 3D45
may result in fire, property damage and
personal injury.
Do not use Dremel 3D45 to create objects
intended for food or drink applications such
as preparation, decoration, storage, or
consumption. Such use of objects created by
Dremel 3D45 may result in illness or personal
injury.
Do not use Dremel 3D45 to create objects
intended with
components or housings of electrical
components. Dremel filament is not suitable
for electrical applications. Such use of objects
created by Dremel 3D45 may result in property
damage and personal injury.
Do not put plastic objects in or around your
mouth. Dremel filament is not suitable for food
or drink preparation and food utensils. Such use
of objects created by Dremel 3D45 may result in
illness or personal injury.
Do not use Dremel 3D45 to create objects
intended for chemical storage. Dremel
filament is not suitable for chemical storage.
Such use of objects created by Dremel 3D45
may result in property damage and personal
injury.
Do not modify Dremel 3D45 or alter factory
settings. Modifications may result in equipment
and property damage, and personal injury.
Do not expose Dremel 3D45 to temperatures
exceeding 70°C (158°F). Dremel 3D45 may
become damaged. Dremel 3D45 is intended to
operate in temperature between 16-29° C (60 -
85° F).
Do not move or bump Dremel 3D45 or the
extruder during operation. The object may
build incorrectly.
Do not change filament spool unless the
building process is completed, stopped, or
paused. Changing the filament during building
will cancel the object and may damage the
extruder.
General Safety Warnings
use with electrical
Do not pull the filament out. Doing so may
damage the extruder.
Use extra care not to damage the extruder
tip when clearing debris. Dremel 3D45 will not
work properly with damaged extruder tip and will
require replacement.
Before every build make sure that the build
platform is covered with Dremel specified
glue. Use of improper glue may result in
equipment damage and poor object build
quality.
Be aware of your body position when using
hand tools to remove objects from the build
platform. Sudden tool slip and improper body
position during object removal from the build
platform may result in personal injury.
Avoid scratching the build platform when
removing objects. Scratches in the build
platform will result in improper object creation.
Do not drop the build platform. Tempered
glass plate may break and result in personal
injury.
Do not remove tempered glass plate from
plastic holder. Contact with tempered glass
plate edge may result in personal injury.
Do not twist or bend the build platform while
removing objects. Tempered glass plate may
separate from plastic holder and result in
personal injury.
Dremel is not responsible for structural
integrity or utility of objects created using
Dremel 3D45. Structural models created by
inexperienced designers may result in property
damage and personal injury.
Service
Always unplug Dremel 3D45 from its power
before performing any service procedures.
Failure to do so may result in personal injury
and equipment damage.
Have your Dremel 3D45 serviced only by an
authorized Dremel service center using only
Dremel replacement parts. This will ensure
that proper operation and safety of Dremel
3D45 is maintained.
Use only Dremel approved components. Use
of components other than genuine Dremel
components may void warranty.
Use only Dremel approved filament. Damage
to the product resulting from use of filament
other than Dremel approved filament is not
covered under warranty.