Tool Use And Care; Service - Ridgid Kollmann SeeSnake KD-200 Consignes De Sécurité

Kollmann
gloves away from moving parts. Loose clothes, jew-
elry, or long hair can be caught in moving parts.
• Avoid accidental starting. Be sure switch is OFF
before plugging in. Carrying tools with your finger on
the switch or plugging in tools that have the switch on
invites accidents.
• Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables bet-
ter control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
• Gloves should always be worn for health and
safety reasons. Sewer lines are unsanitary and may
contain harmful bacteria.
• Heed warnings. All warnings on the product and in
the Operator's Manual should be adhered to.
• Use proper accessories. Do not place this product
on any unstable cart or surface. The product may fall
causing personal injury and/or damage to the product.
• Prevent object and liquid entry. Never spill liquid of
any kind on the product. Never push objects of any
kind into this product through openings as they may
touch dangerous voltage points or short to parts that
could result in a fire or electrical shock.
NOTE! Check to make sure pipe not electrically hot.
In some cases ground circuits may be returned
to cast iron pipes causing them to be electrically
charged. As sections of pipe joined with shielded
hub-less connections or compression gaskets
may be electrically isolated, care should be
taken to check the entire length on any pipe
you are going to inspect.

Tool Use and Care

• Do not use tool if switch does not turn it ON or
OFF. Any tool that cannot be controlled with the switch
is dangerous and must be repaired.
• Store idle tools out of the reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
• Maintain tools with care. Properly maintained tools
are less likely to cause injury.
• Check for misalignment or binding of moving
parts, breakage of parts and any other condition
that may affect the tool's operation. If damaged,
have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
Standard and Mini SeeSnake Diagnostic Equipment
Ridge Tool Company
• Use only accessories that are recommended by the
manufacturer for your tool. Accessories that may be
suitable for one tool may become hazardous when
used on another tool.
• Inspect tool and extension cords periodically and
replace if damaged. Damaged cords increase the risk
of electrical shock.
• Keep handles dry and clean; free from oil and
grease. Allows for better control of the tool.
• Store tools in dry place. Such measures reduce the
risk of electrical shock.
• Protect against lightning. For added protection for
this product during a lightning storm, or when it is
left unattended and unused for long periods of time,
unplug it from the wall outlet. This will prevent damage
to the product due to lightning and power surges.
• Protect against excessive heat. The product should
be situated away from heat sources such as radiators,
heat registers, stoves or other products (including am-
plifiers) that produce heat.
• Provide adequate ventilation. Slots and openings
in the cabinet are provided for ventilation and to ensure
reliable operations of the product. These openings
must not be blocked or covered. This product should
not be placed in a built-in installation such as a rack or
bookcase unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.

Service

• Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified repair personnel could result in injury.
• When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
Section of this manual. Use of unauthorized parts or
failure to follow maintenance instructions may create a
risk of electrical shock or injury.
• Follow instructions for lubricating and changing
accessories. Accidents are caused by poorly main-
tained tools.
• Provide proper cleaning. Unplug this product from the
wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
• Conduct a safety check. Upon completion of any
service or repair of this product, ask the service tech-
nician to perform safety checks to determine that the
product is in proper operating condition.
3