Table Des Matières - VHF K5+ Mode D'emploi

1 Welcome
1.1 About this document
1.2 Used symbols
1.3 Structure of safety notes
2 General safety instructions
3 Operating regulations
3.0.1 Intended use
3.0.2 Controlling the machine through software
3.0.3 Maintenance and cleaning
3.0.4 Spindle
3.0.5 Unattended operation
3.0.6 Transportation and storage
4 Machine overview
4.1 Front side of the machine
4.2 Connection panel
4.3 Working chamber door
4.4 Working chamber
4.5 Accessories container
4.6 Anti-soiling concept
4.7 CAM computer
4.8 Sound emission
4.9 Location of the identification plate & serial number
4.10 Axes
4.10.1 Linear axes
4.10.2 Rotary axes
4.11 Technical data
5 Installing the machine
5.1 Checking the scope of delivery
5.2 Choosing the installation site
5.3 Machine installation (schema)
5.4 Establishing the electric connection
5.5 Removing the transport lock
5.6 Installing the pneumatics
5.6.1 Overview compressed air regulator
5.6.2 Installing the pneumatic hose
5.6.3 Adjusting the air pressure with the compressed air
regulator
5.7 Installing the air extraction system
5.7.1 Requirements for the suction unit
5.7.2 Installing the suction unit
5.7.3 Connecting the suction hose with the optional hose
connection
5.7.4 Installing the switching unit
5.8 Integrating the machine into the network
Contents
5
5
5
5
6
8
8
8
8
8
8
9
10
10
10
10
11
12
12
12
13
13
13
13
13
14
15
15
16
17
18
18
19
20
20
21
22
22
22
22
23
24
Original Operating Instructions: K5+
Version: 12/16/2021
5.9 Configuring the webcam
5.9.1 What to do when devices are in use in SX Virtual
Link
5.9.2 What to do if the machine is unreachable
5.9.3 Network configuration via the machine's web
server
5.9.4 Resetting the network configuration to factory
defaults
6 Operation: Preparing jobs
6.1 Starting the machine
6.2 Starting the machine with a tool in the collet chuck
6.3 Switching off the machine
6.4 Mounting & removing blanks
6.4.1 Mounting discs in the working chamber
6.4.2 Mounting blocks to the block holder
6.4.3 Mounting the block holder in the working chamber 34
6.4.4 Using an optional abutment holder
6.5 Managing tools
6.5.1 Inserting and exchanging tools
6.6 Deactivating and activating the ionizer
7 Operation: Executing jobs
7.1 Starting jobs
7.2 Aborting machining
7.3 Job interruptions and job abortions
7.3.1 How to proceed in case of a job interruption
7.3.2 How to proceed in case of a machine malfunction 38
7.3.3 How to proceed in case of a tool breakage
7.3.4 How to proceed in case of a power failure
7.4 Emergency opening of the working chamber door
8 Maintenance and do-it-yourself
8.1 Maintenance section
8.2 Basic maintenance
8.3 Preventive maintenance
8.4 Where to get service?
8.5 Definition of wear parts
8.6 Cleaning the working chamber
8.7 Cleaning the collet chuck
8.8 Checking the compressed air regulator
8.8.1 Checking the water separator for condensate
8.8.2 Exchanging / cleaning the contaminated filter cart-
ridge
8.9 Cleaning the housing
8.10 Exchanging the main fuse
8.11 Calibrating the axes
8.12 Replacing the tool magazine inserts
EN 3
27
28
28
28
28
29
29
30
30
31
31
32
34
34
35
36
37
37
37
38
38
38
39
39
41
41
41
41
41
41
42
43
45
46
46
46
46
47
48