Char-Broil Patio Bistro 360 Mode D'emploi page 8

Ignitor Lighting
READ INSTRUCTIONS BEFORE LIGHTING.
Do NOT lean over appliance while lighting.
1. Turn OFF gas burner control valve.
2. Turn ON gas at LP gas cylinder.
3. Open lid during lighting.
4. Press and turn the control knob to
5. Push and hold ELECTRONIC IGNITOR button until the burner lights
6. Once ignited, turn control knob to desired setting.
7. Repeat lighting procedure for second burner.
8. If ignition does not occur in 5 seconds, turn the burner control knob
OFF, wait 5 minutes, and repeat lighting procedure.
WARNING
Turn control knob and LP cylinder OFF when not in use
CAUTION
If ignition does NOT occur in 5 seconds, turn the
control knob OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
Do NOT lean over appliance while lighting.
1. Turn OFF gas burner control valve.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. Insert match into match holder. Light match. Place lit match into
match light hole at the rear of the grill bottom, shown "A". Make sure
lit match is placed inside through the hole and near burner.
5. Push in and turn control knob to position 5 . Be sure burner lights
and stays lit.
6. Repeat match-lighting procedure for second burner.
A
Rotate Match
Light Hole
Cover
.
.
Match Light Hole
View is from
rear of appliance
Burner Flame Check
• Light burner. Looking through the match light hole underneath
the appliance, you should see the flame height as shown
below. Turn control knob from position 5 to 1 . The Flame
height should decrease. Always check flame prior to each use.
If only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
.
Turning Appliance Off
• Turn control knob to
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas OFF at LP cylinder. Turn ignitor knob. "Click" should
be heard each time at electrode. See "Troubleshooting" if no
click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valve. Knob locks in
valve, first push in knob and release, knob should spring back.
If knob does not spring back, replace valve assembly before
using this appliance. Turn knob to position 1 then turn back
to OFF position. Valve should turn smoothly.
Hose Check
• Before each use, check to see if hose is cut, worn or kinked.
Replace damaged hose before using appliance. Use only
valve/hose/regulator specified by manufacturer.
Normal
Hose
General Appliance Cleaning
• Meat Thermometer: Do not immerse or soak in water. Wash
with warm soapy water and wipe dry.
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors are not painted at the factory (and
should never be painted). Apply a strong solution of detergent
and water or use a grill cleaner with scrub brush on insides of
appliance lid and bottom. Rinse and allow to completely air dry.
Do not apply a caustic grill/oven cleaner to painted
surfaces. A black surface improves the appliances
performance.
• Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Painted surfaces: Wash with mild detergent or non-abrasive
cleaner and warm soapy water. Wipe dry with a soft non-
abrasive cloth.
• Cooking surfaces: If a bristle brush is used to clean any of the
grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
8
HIGH 5
LOW 1
OFF position. Turn LP cylinder OFF by
OFF position. To check
Kinked
Hose