Carel MChiller Mode D'emploi page 103

Index Size Ref. Type Min/Max
40 1 S062 BOOL
41 1 S063 BOOL
42 1 S064 BOOL
44 1 S065 BOOL
46 1 S068 BOOL
47 1 UoM BOOL
48 1 Hc02 BOOL
49 1 Hc12 BOOL
50 1 Hc13 BOOL
52 1 Ha02 BOOL
53 1 Hd03 BOOL
54 1 UnSt BOOL
55 1 ModE BOOL
56 1 RES BOOL
59 1 ClrH BOOL
63 1 Hd05 BOOL
64 1 BOOL
66 1 P016 BOOL
67 1 P017 BOOL
68 1 P018 BOOL
69 1 P034 BOOL
80 1 U078 BOOL
7.2 Input status
Index Size Ref. Type Min/Max
0 1 A01 BOOL
1 1 A02 BOOL
2 1 A03 BOOL
3 1 A04 BOOL
4 1 A05 BOOL
5 1 A06 BOOL
7 1 A08 BOOL
8 1 A09 BOOL
9 1 A10 BOOL
10 1 A11 BOOL
11 1 A12 BOOL
12 1 A13 BOOL
13 1 A14 BOOL
14 1 A15 BOOL
15 1 A16 BOOL
16 1 A17 BOOL
17 1 A18 BOOL
18 1 A19 BOOL
19 1 A20 BOOL
20 1 A21 BOOL
21 1 A22 BOOL
22 1 A23 BOOL
23 1 A24 BOOL
24 1 A25 BOOL
25 1 A26 BOOL
26 1 A27 BOOL
µChiller +0300053FR rel. 1.3 – 30.10.2019
R/W UoM Description
R/W S062 - Source pump output logic (0=N.O., 1=N.C.)
R/W S063 - Reverse valve output logic (0=N.O., 1=N.C.)
R/W S064 - Source flow type (0=Independent, 1=Common)
R/W S065 - Source fan type (0=Inverter, 1=ON/OFF)
R/W S068 - Source type (0=Air, 1=Water)
R/W UoM - Unit of measure used for Display 2-Row and BMS, not for Applica (0=°C/bar, 1=°F/PSI)
R/W Hc02 - Analog channel 4 enabling (0=Disabled, 1=Enabled)
R/W Hc12 - Digital output 6 config. (0=Antifreeze, 1=Source fan / Source pump)
R/W Hc13 - Enable buzzer (0=Disabled, 1=Enabled)
R/W Ha02 - Sets controller internal clock (0=No set, 1=Set)
R/W Hd03 - Enable NFC (0=Disabled, 1=Enabled)
R/W UnSt - Unit ON/OFF command by keyboard (0=OFF 1=ON)
R/W ModE - Cool/Heat mode by Keyboard (0=Cool, 1=Heat)
R/W RES - Reset active alarms by BMS net (0=NO, 1=Reset)
R/W ClrH - Delete alarms log (0=No, 1=Yes)
R/W Hd05 - Enable unit ON/OFF command by BMS net (0=Disabled, 1=Enabled)
R/W Unit ON/OFF command by BMS
R/W P016 - Oil equalization solenoid valve circ.1 output logic (0=NC, 1=NO)
R/W P017 - Enable oil equalization function (0=OFF, 1=ON)
R/W P018 - Enable oil recovery function (0=OFF, 1=ON)
R/W P034 - Enable cranckcase heater (0=OFF, 1=ON)
R/W U078 - Burst function enabling (0=Disabled, 1=Enabled)
R/W UoM Description
R Unit - Error in the number of retain memory writings
R Unit - Error in retain memory writings
R Unit - Remote alarm by digital input
R Unit - Alarm remote set point out of range
R Unit - Alarm user return water temperature probe broken or disconnected
R Unit - Alarm user delivery water temperature probe broken or disconnected
R Unit - User pump 1 overload
R Unit - User pump 2 overload
R Unit - Flow switch alarm, no flow present with user pump 1 active
R Unit - Flow switch alarm, no flow present with user pump 2 active
R Unit - User pumps group alarm
R Unit - User 1 pump maintenance
R Unit - User 2 pump maintenance
R Unit - High chilled water temperature
R Unit - Alarm source return water/air temperature probe broken or disconnected
R Unit - Source 1 pump maintenance
R Unit - Free-cooling anomaly
R Circuit 1 - Alarm discharge pressure probe broken or disconnected
R Circuit 1 - Alarm condensing temperature probe broken or disconnected
R Circuit 1 - Alarm suction pressure probe broken or disconnected
R Circuit 1 - Alarm evaporating temperature probe broken or disconnected
R Circuit 1 - Alarm discharge temperature probe broken or disconnected
R Circuit 1 - Alarm suction temperature probe broken or disconnected
R Circuit 1 - High pressure alarm by pressure switch
R Circuit 1 - High pressure alarm by transducer
R Circuit 1 - Low pressure alarm by transducer
7. Tableaux supervision | 103
FRE
Tab.7.a