Before Starting The Equipment - EINHELL TE-SD 3,6/1 Li Instructions D'origine

Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 57,3 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 68,3 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Screwing without hammer action
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
Anl_TE_SD_3_6_1_Li_SPK9-1.indb 16 Anl_TE_SD_3_6_1_Li_SPK9-1.indb 16
≤ 2,5 m/s
2
h
2
- 16 -
GB
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Danger!
Be sure to read the following information before
you put the cordless screwdriver into operation:
1. Charge the battery only with the charging unit
supplied.
2. Only ever use screwdriver bits which are
suitable for the purpose and in faultless con-
dition.
3. Before you begin to screw in walls and ma-
sonry, check for concealed electric wiring,
gas pipes and water pipes.
6. Operation
6.1 Charging the battery (Fig. 2)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is
fl at. In this case the bit chuck will cease to turn.
Important! Do not actuate the On/Off switch any
more if the protective circuit has tripped. This may
damage the battery.
Check that your mains voltage is the same as
that marked on the rating plate. Connect the type
A USB connector (8a) of the charging cable (8)
to the charger (7). Plug the battery charger in the
plug socket and connect the type B USB connec-
tor (8b) of the charging cable (8) to the charging
connection (6) of the cordless screwdriver.
The charging indicator light (5) will light up red to
indicate that the battery pack is being charged.
When charging is fi nished, the charging indicator
light changes to green.
Notice! The handle may become a little warm du-
ring the charging process. This is normal.
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
21.12.2017 14:51:35 21.12.2017 14:51:35