Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL BT-SH 90/350 Mode D'emploi

Anleitung_BT_SH_90_350_SPK7:_
(11). The saw blade support (11) should be
positioned as close as possible to the grinding
point (Fig. 14).
Now move the grinding wheel (10) using the
handle (7) between the teeth of the saw blade so
that when the saw blade is turned clockwise
against the grinding wheel (10) the whole surface
area of the carbide metal plate on the saw blade
lies flat on the grinding wheel (10) (Fig. 15 – 17).
Important. Do not move the motor so far
forwards that the saw blade can be touched by
the grinding wheel.
Adjust the stop (14) so that the grinding wheel
(10) cannot be moved beyond this position into
the saw blade and secure it in this position using
the Allen screw (L) (Fig. 18).
6.3 Setting the tooth set angle
In addition to the tilt angle of the motor (5), the saw
blade set must be adjusted accordingly for set saw
blades. For this purpose undo the two nuts (H), tilt
the motor (5) until the required angle is shown on the
scale (13) and secure it by tightening the two nuts
(H) (Fig. 19 – 20).
7. Operation
7.1 ON/OFF switch (Fig. 2 / Item 15)
Set the ON/OFF switch (15) to the "I" position to
switch on the equipment.
Set the ON/OFF switch (15) to the "0" position to
switch off the equipment.
7.2 Grinding saw blades
Proceed as follows to grind saw blades:
Switch on the equipment (see 7.1)
Turn the saw blade so that the grinding wheel
(10) is between the saw blade teeth and then
move the grinding wheel (10) as far as possible
to the front using the handle (7) (Fig.15-16).
Turn the saw blade slowly and carefully in a
clockwise direction into the rotating grinding
wheel (10) and grind the carbide metal plates on
the saw blade until their cutting edge has been
sharpened (Fig. 17). When the grinding wheel is
at 12 o'clock, your hands must be at 3 o'clock
and 9 o'clock on the saw blade.
Turn the saw blade back anti-clockwise so that
the grinding wheel (10) can run freely between
the saw blade teeth. Move the motor (5) to the
rear again using the handle (7).
Turn the saw blade one tooth further and repeat
the process until you have sharpened all the
teeth.
21.09.2009 9:20 Uhr Seite 17
7.3 Grinding set saw blades
To grind saw blades with set teeth, the motor (5)
must be titled to the set angle of the saw blade
as described in point 6.3.
Then proceed as described in point 7.2 but in
this case every second tooth must be ground
according to its set.
Then adjust the angle to the set of the teeth you
have not yet ground (see point 6.3) and grind
those teeth as described above.

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
9.2.1 Replacing the grinding wheel
When the grinding capacity of the equipment falls
noticeably, the grinding wheel should be replaced.
Undo the three screws (M) on the grinding wheel
cover (8) and remove it (Fig. 21).
Place the pin (C) in the opening (I) and slowly
turn the grinding wheel (10) by hand until the pin
(C) blocks the equipment's drive shaft (Fig. 22).
Position a wrench on the flange nut (J), hold the
pin (C) and undo the flange nut (J) by turning it
anti-clockwise (Fig. 23).
Remove the flange nut (J), external flange (K)
and grinding wheel (10). Clean the flange and fit
the new grinding wheel using the above
instructions in reverse and secure it.
GB
17