General Safety Instructions; Overview Of The Components; Instruction Manual - AEG MRC 4102 Mode D'emploi & Garantie

General safety instructions

To avoid the risk of fi re or an electric shock, you should
not expose the device to rain or moisture. Consequently,
do not use the device in the immediate vicinity of water
- for example near a bath tub, a swimming pool or in a
damp cellar.
Use the device only for the intended purpose.
Only connect the device at a properly installed plug so-
cket. Pay attention that the specifi ed voltage corresponds
to the voltage of the plug socket.
When using external mains supply, pay attention to the
correct polarity and voltage. Always place the batteries in
the correct direction.
Assemble the device in such a way that the available
ventilation openings are not covered.
Never open the housing of the device. Incorrect repairs
can constitute a considerable risk for the user. Should the
device become damaged, in particular the mains supply
cable, do not operate the device any longer, but rather
have it repaired by an expert. Check the mains supply
cable regularly for damage.
For safety reasons a broken or damaged mains lead may
only be replaced by an equivalent lead from the manuf-
acturer, our customer service department or a similary
qualifi ed person.
If the device is not used for a longer period, remove
the plug connector from the plug socket or take out the
batteries.
These symbols may be found on the machine and are
intended to indicate the following:
The lightning symbol should advise the user
of parts in the inside of the device which carry
dangerously high voltage levels.
The symbol with an exclamation mark should
advise the user of important operation or
maintenance instructions in the accompanying
documentation.
Devices bearing this symbol work with a
„class 1 laser" for tracing the CD. The built-in
safety switches should prevent the user being
exposed to dangerous laser light, which is
invisible to the human eye, when the CD compartment is
opened.
Under no circumstances should these safety switches be
bypassed or manipulated, as this could result in a danger
of exposure to the laser light.
18
05-MRC 4102 18

Overview of the Components

1 Set minutes (MINUTE)
2 Hour function key (HOUR)
3 Time setting function key (TIME)
4 Alarm function key (ALARM)
5 Function key for delayed switch-off (SLEEP)
6 Wake-up interval (SNOOZE)
7 Function switch (AUTO/OFF/ON)
8 LED for activated alarm function (AUTO)
9 Station scale
10 TUNING regulator
11 LED
12 BUZZ / OFF / VOL (volume) regulator
Putting into function
Insert the plug into a properly installed 230 V, 50 Hz
power socket.
Radio station tuning
Push the function switch (7) to the ON position and select
a station by turning the TUNING control (10). The station
scale (9) indicates the selected frequency.
If reception is too weak and the station being received
hisses, try to improve reception by turning, unwinding or
winding up the throw-out antenna.
Volume
The desired volume can be sent using the VOL(UME)
regulator (12).
Setting of the Clock (24 h)
Hours: Press the TIME key (3) and the HOUR key (2)
simultaneously.
Minutes: Press the TIME key (3) and the MINUTE key
(1) simultaneously.
Setting of the Alarm (24 h)
Hours: Press the ALARM key (4) and the HOUR key
(2) simultaneously.
Minutes: Press the ALARM key (4) and the MINUTE
key (1) simultaneously.
Radio alarm
• Once the alarm times are set and a radio station
has been selected, shift the function selector (7) to
„AUTO". A dot in the display (11) appears next to
AUTO (8).
• As soon as the alarm time is reached, the radio is
switched on. The selected radio station plays at the
set volume.
To turn the radio off simply press the ALARM button.
Buzzer alarm
• If you would not like to be woken up by the radio, turn
the volume control (12) to the BUZZ position (buzzer)
until it locks in place.
• Instead of the radio, the buzzer goes off when the
alarm time is reached.
To turn off the alarm, push the function switch (7) to the
OFF position or press the ALARM button (4).
25.04.2005, 14:29:44 Uhr