Automatic Safety Cut-Out; Care And Cleaning; Cleaning Agents; Malfunction Table - Blaupunkt 5MA46500 Notice D'utilisation

Masquer les pouces Voir aussi pour 5MA46500:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Automatic safety cut-out

The automatic safety cut-out is activated if your appliance is
operating for a long time with no cooking time having been set.
The time at which your appliance switches itself off depends on
the set type of heating and temperature.

Care and cleaning

With careful care and cleaning your microwave oven will retain
its looks and remain good order. We will explain here how you
should care for and clean your appliance correctly.
:
Risk of electric shock!
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
:
Risk of burns!
Never clean the appliance immediately after switching off. Let
the appliance cool down.
:
Risk of serious damage to health!
Microwave energy may escape if the cooking compartment
door or the door seal is damaged. Never use the appliance if
the cooking compartment door or the door seal is damaged.
Contact the after-sales service.
Notes
Slight differences in colour on the front of the appliance are
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
Unpleasant odours, e.g. after fish has been prepared, can be
removed very easily. Add a few drops of lemon juice to a cup
of water. Place a spoon into the container as well, to prevent
delayed boiling. Heat the water for 1 to 2 minutes at
maximum microwave power.

Cleaning agents

To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
sharp or abrasive cleaning agents,
metal or glass scrapers to clean the glass in the appliance
door.
metal or glass scrapers to clean the door seal,
hard scouring pads and sponges,
cleaning agents with high concentrations of alcohol.
Wash new sponge cloths thoroughly before use.

Malfunction table

Malfunctions often have simple explanations. Please refer to the
malfunction table before calling the after-sales service.
If a meal does not turn out exactly as you wanted, refer to the
Tested for you in our cooking studio section, where you will
find plenty of cooking tips and tricks.
Example: If your oven is operating with Hot air at 160 °C, it will
automatically switch off after approx. 5 hours.
appears in the display panel. The appliance switches off.
Touch any button or turn the rotary selector.
Allow all surfaces to dry thoroughly before using the appliance
again.
Area
Cleaning agents
Appliance front
Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaners or
metal or glass scrapers for cleaning.
Appliance front with
Hot soapy water:
stainless steel
Clean with a dish cloth and dry with a
soft cloth. Remove flecks of limescale,
grease, starch and albumin (e.g. egg
white) immediately. Corrosion can form
under such residues. Special stainless
steel cleaning agents can be obtained
from the after-sales service or from spe-
cialist shops. Do not use glass cleaners
or metal or glass scrapers for cleaning.
Cooking compart-
Hot soapy water or a vinegar solution:
ment
Clean with a dish cloth and dry with a
soft cloth.
If the oven is very dirty: Do not use oven
spray or other aggressive oven cleaners
or abrasive materials. Scouring pads,
rough sponges and pan cleaners are
also unsuitable. These items scratch the
surface. Allow the interior surfaces to
dry thoroughly.
Recess in cooking
Damp cloth:
compartment
Ensure that no water seeps through the
turntable drive into the appliance inte-
rior.
Wire racks
Hot soapy water:
Clean using stainless steel cleaning
agent or in the dishwasher.
Door panels
Glass cleaner:
Clean with a dish cloth. Do not use a
glass scraper.
Seal
Hot soapy water:
Clean with a dish cloth, do not scour. Do
not use a metal or glass scraper for
cleaning.
:
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
31

Publicité

Table des Matières
loading

Table des Matières