Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
• Only groups A,B or C which are in M or TTL mode will be
adjusted
• Both "Manual" and "TTL" modes can be adjusted
simultaneously by one relevant increment. (i.e. one
increment of manual power may be more than one
increment of TTL FEC compensation)
Multi : Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes are fired.
It can be used to capture multiple images of a moving
subject in a single photo. You can set the firing frequency
25
(number of flashes per second expressed in Hz), the
number of flashes
24
, and the flash output
1. Press
A
button for more than 3 seconds so that
<MT> mode is displayed
2. Press <SEL>
02
button and all icons for
C
will flash
A
button to select <T> the number of times the
3. Press
flash will flash
•
Turn <Adjust Dial>
•
Press
B
to select "Hz" the flash frequency
•
Turn <Adjust Dial>
flashes
4. Press
C
to select the flash output level
•
Turn <Adjust Dial>
•
In <MT> mode the max power level 1/4
5. Then press button <SEL>
Pressing button
A
or
B
group
Pressing button
A
for more than 3 seconds will exit
"MULTI MODE" and return to standard Manual/TTL /OFF
setting
• For "Nikon" version the RPT repeating flash mode is
only available when used with the hahnel Modus 600RT
Speedlight. Check our website www.hahnel.ie for future
firmware updates which may enable this feature when using
the Nikon Viper TTL receiver with original Speedlight's.
High Speed Sync
Press and hold button
B
the icon
20
will switch on. High speed sync applies to all
groups at the same time.
• For "Nikon" version ensure also that the camera setting is
set to 1/320's (Auto FP) or 1/320's (Auto FP). Both Viper
transmitter and Camera menu must be set to HSS. Refer
to camera manual for more info.
6
26
A
,
B
and
03
to set the number of flashes
03
to adjust the frequency of
03
to adjust the output power
02
to save the setting
or
C
will turn ON/OFF each
to switch on high speed sync -
Viper TTL - English
Second Curtain Sync
When the high speed sync icon
and hold button
B
again to switch on second curtain
sync - the icon
21
will switch on. Second curtain sync
applies to all groups at the same time
To return to normal sync, press and hold button
until the icon
21
switches off
• For "Nikon" version, the Second Curtain Sync (Rear-
curtain sync) is not controlled from the Viper TTL. To
enable Second Curtain Sync set in the camera menu to
Rear-curtain sync. Refer to camera manual for more info
Always On
Press and hold the <SEL>
while you switch on the transmitter. The battery indicator
23
will flash. Turn Adjust Dial
(
displayed. Now turn OFF and ON
Always ON feature. When Always ON the Viper TTL is
permanently transmitting a signal.
Battery Level
•
The transmitter LCD shows the level of the battery for
the transmitter
23
•
To check the receiver battery level, check LED
which flashes green to indicate normal power
Viper TTL transmitter hot shoe
The camera mounted Viper TTL transmitter has a built
in hot shoe
07
. A Speedlight fitted to this hot show will
operate as Group
A
for Canon version and Group
Nikon version.
• For the Nikon version group (M) is controlled by the
setting of the camera and not controlled by any of the
Viper TTL groups
DCM Digital Channel Matching
•
Open channel - When you use the Viper TTL for the
first time, the 2.4GHz wireless connection is using a
default "open channel". This allows several transmitters
to individually control the same selection of receivers.
The "open channel" can be useful when using several
cameras with the same lighting system. But it is also
more prone to other outside interferences
•
DCM - Digital Channel Matching is a more secure
coded wireless system which will avoid any external
interference between Viper TTL transmitter and
receiver. Carry out the following set up to match all
Viper TTL - English
20
is switched on, press
B
again,
02
button and keep it pressed
03
until Always ON
22
is
01
again to enable the
11
M
for
7
Publicité
Table des Matières
