Connecting To The Water Supply; Connecting To The Water Tap; Connecting The Drain Hose - SCHOLTES LTE S3 XL60HZ Instructions Pour L'installation

5.2.1 Connecting to the water supply

EN
Preventing the risk of clogging or damage:
If the water pipe is new or has not been used for a long
time, before connecting to the water supply check that
the water is clear and free of impurities, to prevent
damage to the appliance. The dishwasher must always
be connected to the water system with new hoses; old or
used hoses must never be reused.

5.2.1.1 Connecting to the water tap

Connect the inlet hose to a threaded ¾" gas cold water
tap, fitting the supplied filter (ref. A fig. 5-06).
Fir Fir mly secur mly secur e the hose by tightening the r e the hose by tightening the r
Fir Firmly secur Fir mly secure the hose by tightening the r mly secur e the hose by tightening the r e the hose by tightening the relative ring nut
with your hands (r with your hands (ref. B fig. 5-06); finish by tightening with your hands (r with your hands (r with your hands (r ef. B fig. 5-06); finish by tightening ef. B fig. 5-06); finish by tightening ef. B fig. 5-06); finish by tightening ef. B fig. 5-06); finish by tightening
another ¼ turn using a pair of plumbing pliers. For another ¼ tur another ¼ tur another ¼ tur another ¼ tur n using a pair of plumbing pliers. For n using a pair of plumbing pliers. For n using a pair of plumbing pliers. For n using a pair of plumbing pliers. For
models fitted with ACQUASTOP (r models fitted with ACQUASTOP (r models fitted with ACQUASTOP (ref. C fig. 5-06) the models fitted with ACQUASTOP (r models fitted with ACQUASTOP (r
filter is already pr filter is alr filter is alr eady pr eady present in the thr eady pr esent in the thr esent in the threaded ring nut. esent in the thr
filter is alr filter is alr eady pr esent in the thr
The dishwasher can be filled with water at a temperature
of less than 60°C (140°F). If the appliance is filled with
hot water, washing times will be reduced by about 20
minutes, but efficiency will be slightly impaired. Make the
connection to the domestic hot water tap using the same
methods described for connecting the appliance to the
cold water tap.
•
Recommended temperature: 49°C (120°F), max. 60°C
(140°F).
•
Recommended water pressure: 0.5 - 9 bar (7-130
PSI).
If the pressure is too high, fit a pressure reducer.
A rubber hose connected to a sink spray may burst if
installed on the same pipes feeding the dishwasher.
If your sink is fitted with this accessory, remove the
hose and plug the hole.
Fig. 5-06
Do not cut the inlet hose (see fig. 5-07).
If the hose is cut, the dishwasher will not work, water will
leak and you may be injured. If the hose is too long, wind
it up tidily and place it behind the appliance.
The cable harness and electrical components must not
10
elative ring nut elative ring nut
elative ring nut elative ring nut
ef. C fig. 5-06) the ef. C fig. 5-06) the ef. C fig. 5-06) the ef. C fig. 5-06) the
eaded ring nut. eaded ring nut. eaded ring nut.
eaded ring nut.
come into contact with the hydraulic system and the
water inlet and drain hoses.
Fig. 5-07
When connecting the dishwasher drain hose to the sink
make sure that the hose is not bent (ref. A fig. 5-08) in order
to prevent cracks or breakages that could damage it.
Fig. 5-08

5.2.1.2 Connecting the drain hose

Connecting to a drain
Insert the relative hose into a drain with a minimum
diameter of 4 cm (1-37/64") (ref. A fig. 5-09); alternatively,
place the hose on the sink (ref. B fig. 5-09) using the
supplied hose support (see fig. 5-10), but taking care to
avoid obstructions or excessive curving. Make sure the
hose cannot fall out. For this purpose, the hose support is
fitted with a hole (ref. A fig. 5-10) which can be used to fix
it to the wall or the tap with a piece of string. The free end
must lie at a height ranging from of 30 to 100 cm (from of
1-7/32" to 3-59/64") (see fig. 5-09) and must never be
immerged in water. If horizontal extension hoses with a
maximum length of 3m are used, position the drain hose
at a maximum height of 85 cm (3-11/32") above the floor.
Fig. 5-09