Sanisan 1 Mode D'emploi page 9

8
NORM
• SANISAN conforms to EN 12050-3.
®
Lifting plant for wastewater containing faecal matter for
limited applications.
9
COMMISSIONING THE UNIT
Once electrical and plumbing connections have been made,
flush the WC once. The motor should run from 10 to 30
seconds to clear the waste (depending on the length and
height of the pipe run). If it runs for more than 35 seconds,
check that the pipework is clear, and that the discharge
hose is not kinded, or that the non-return valve
correctly installed.
Flush the WC checking that all seals, and connections are
watertight. Check both the discharge pipework from the unit,
and the waste pipes from washbasin (S2 or S3) or shower
(S3).
WARNING: There should be no dripping of water from the
WC cistern or taps. If there is, this will cause the unit to
activate repeatedly as it pumps the water away.
1 0
USAGE
A WC fitted with a SANISAN
require any special maintenance. The SANISAN
operate automatically as soon as the required level
of water enters the case.
WARNING: The SANISAN
the evacuating of normal human waste, toilet paper and
household WC cleansers. Damage may occur to the
machine if the following are disposed of via the WC;
Cotton wool, tampons, sanitary towels, wet wipes, kitchen
towels, condom as well as other fabric or hard objects.
Solvents, acids and other chemicals can olso cause
damage to the unit, and will invalidate the warranty.
1 0
CARE OF YOUR SANISAN
• Normal household bleaches/WC cleansers can be used
with a SANISAN .
®
• To avoid the build up of limescale in the unit, use the
following procedure.
- disconnect the power supply to the unit,
- pour 3 or 4 litres of water mixed with a strong solution
of descalent/spirit of salts into the WC pan,
- leave it to stand for 1 or 2 hours, then re-connect the
electric supply,
- flush several times to clear.
The frequency of this operation will depend on the
hardness of the water in your locality. We would
recommend this be done about twice a year.
is
D
® pump/macerator does not
will
®
® range should only be used for
UNIT
®
1 2
FAULT FINDING/REMEDIES
For the most part any inconsistencies in the operation of the
unit will be minor and easily rectified. Please refer to the chart
below. If the problem cannot be easily remedied in this way.
Please call our Service organisation.
Warning - Always disconnect the electricity supply
before attempting any work on the SANISAN
SYMPTOM PROBABLES CAUSES
• The motor intermittent- • The WC cistern or taps
ly are dripping
activates
• The external non-return
valve D is faulty
• The water in the WC pan • The inner grille is clog-
goes down very slowly ged up
• The motor operates nor- • The length or height of
mally, but continues to the installation is over
run for a long time the specification, or
there are too many
bends/elbows
• The pump itself is
blocked
• The activating pressure
membrane is distorted
• The motor does not • The electrical supply is
activate not active
• The motor is defective
• The motor omits a ratt- • A foreign object has
ling or crunching sound entered into the grille
via the WC pan
• The motor hums, but • The capacitor or motor
does not run is defective
1 3
REMOVAL
Any replacement of the power supply cable should only be
carried out by an authorised SANISAN service engineer.
REMOVING THE SANISAN FROM THE WC SUITE
Disconnect the electrical power supply
A
Turn off the water feed to the WC cistern. Bail out as much
B
water as possible from the cistern.
Disconnect the discharge pipe.
C
In thecase of S2 and S3, disconnect the inlet connections.
D
Remove the 2 screws, which secures the Sanisan on the ground.
E
Ease the flexible connector off the WC pan spigot and slide
F
the sanisan out from behind the WC.
REMOVING THE MOTOR FROM THE CASE
Remove the lid (using a torx T20 screwdriver).
G
In the case of S3, undo the 2 screws, which secure the motor
H
to the case.
Loosen the cable clip.
I
Lift the motor block out of the case.
J
NOTE: For easy replacement of the lid, lubricate the lid seal with liquid
soap.
Do not reconnect the electrical power supply until the
re-installation is complete.
1 4
GUARANTEE
The SANISAN ® range is guaranteed for 2 years, subject to
correct installation and usage.
REMEDIES
• Check the appropriate
washers/seals on the
cistern/taps etc
• Clean or replace the
non-return valve
• Call a service engineer
to clear the grille
• Check the installation
• Call a service engineer
to unblock the unit
• Call a service engineer to
replace the membrane
• Restore the electrical
supply
• Call a service engineer
to inspect the motor
• Call a service engineer
to remove the foreign
object from the unit
• Call a service engineer
to inspect the motor