Sanisan 1 Mode D'emploi page 8

UK
10/02
1
DESCRIPTION
The SANISAN range of pump/macerators have been
®
designed to pump away the waste from a WC and a
washbasin and a shower (see
The SANISAN ® models are for domestic use only.
Installed and used correctly, SANISAN
consistent and reliable service.
Please not the following warning signs:
" " Possible danger to personnel,
" " Warning of possible electrical hazard,
"WARNING" This is a general warning that failure to
follow instructions could result in poor functioning
of the unit.
2
LIST OF ACCESSORIES INCLUDED
3
DIMENSIONS
4
TECHNICAL DATA
SANISAN 1 (S1) SANISAN 2 (S2) SANISAN 3 (S3)
Application 1 WC
Type LA01-X10
Maximum Vertical
1 m
Pumping
Voltage 220-240 V
Frequency 50 Hz
Maximum Power Rating 600 W
Maximum current
2,6 A
consumption
Electric Class
I
Degree of protection IP44
Net Weight 5,0 kg
WARNING: Only installations conforming to the above
specifications are acceptable.
5
PERFORMANCE CURVE
6
VERTICAL/HORIZONTAL PUMPING
COMBINATIONS
7
INSTALLATION
must be connected to WC pan with a
WARNING: SANISAN ®
horizontal otlet spigot conforming to EN33 or EN 37.
The macerator and its connections is integral with the
WC pan itself. The access to the apparatus must be
facilitated for control and maintenance.
The crusher has fastenings preventing it turning or from
floating.
7a
CONNECTION TO A WC
Pull the flexible sleeve over the pan spigot
1
Position the jubilee clip over the edge of the flexible sleeve,
2
and tighten with a screwdriver
below for full usage details).
2
will give
®
1 WC 1 WC
+ Washbasin + 1 Washbasin
+ 1 shower
LA02-X11 LA03-P20
4 m 4 m
220-240 V 220-240 V
50 Hz 50 Hz
720 W 550 W
3,2 A 2,5 A
I I
IP44 IP44
5,0 kg 6,8 kg
7b
CONNECTION OF DISCHARGE PIPE TO SANISAN
Insert one of the elbow
A
and turn in the required direction. Secure with jubilee clip.
Fit the flexible hose to the other end of elbow
C
Connect
• a 22mm discharge pipe (copper or CPVC) to the flexible
hose , and secure with a jubilee clip.
C
• alternatively fit a 32/22mm reducer
and install with 32mm pipework.
7c
CONNECTION OF THE DISCHARGE PIPEWORK
TO SANISAN 2 AND SANISAN
®
Insert the elbow into the exit pipe from the unit, and turn
A
it to the direction required. Fit the non-return valve
other end.
WARNING: The non-return valve
positioned so that the embossed arrow is on the top,
and pointing in the direction of flow.
Connect the discharge pipework directly onto the non-return
valve in 20/28mm. Alternatively, cut back the end of the
non-return valve and fit 28/32mm discharge pipework.
Secure both ends of the non-return valve with jubilee clips
7d
CONNECTION OF WASHBASIN SANISAN
AND SANISAN ® 3
Use a suitable cutter to make the opening for the washbasin
entry. There is a ridge where the hole has been partially
pre-cut. Cut the hole with care and deburr it, to avoid leaks
when the adapter is fitted. Insert the adapter
F
Slide the washbasin waste pipe into the adapter.
7e
CONNECTION OF A SHOWER
Use the flexible connector
1
shower waste to one of the side inlets. Secure with
plastic clips and
I H
blanking plug after greasing the joints.
J
WARNING: Ensure when connecting a shower to the
2
SANISAN that the underside of the shower tray is
®
raised by at least 12mm from the floor.
7f
EXAMPLE OF SANISAN
7g
EXAMPLE OF SANISAN
7h
EXAMPLE OF SANISAN
7i
ELECTRICAL CONNECTION
The electrical installation should be carried out by a
qualified person, and conform to BS 7671 1992 requi-
rements for electrical installation.
• The SANISAN requires a 220/240V single phase 50 Hz
®
supply (UK specification) and should be connected to an
unswitched fused wiring connector protected by a 5 amp
fuse, or circuit breaker set to 30mA.
• The unit should be sited at least 6m away from a shower
tray.
into the exit pipe from the unit,
.
A
into the hose,
K
3
®
should be
D
2
®
into the lid.
F
to connect the
G
. Plug the unused inlet with
® 1 INSTALLATION
® 2 INSTALLATION
® 3 INSTALLATION
® 1
to the
D
.
B