Reversible Door; Temperature Control - SEVERIN KS 9760 Mode D'emploi

Caution: Ensure at all times that the rear ventilation
openings around the top cover are not obstructed.

Reversible door

If required, the door may be reversed, i.e. from right-hinged (default
installation) to left-hinged.
To avoid the risk of personal injury or damage to the unit, two people
are needed to reverse the door.
Warning: Always disconnect the unit from the mains before
any maintenance or repair work is carried out.
Before you get started, please note the following:
∙ Always ensure that the correct number of washers is used
on all hinge bolts and screws.
∙ So that the doors can close tightly against the frame, take
the utmost care that they are properly aligned during re-
assembly.
∙ Remove the two spacers (2) on the rear of the unit.
∙ Open the freezer door (18).
∙ Remove the fi xing screws (1 and 3) from the top cover (two
screws at the front and two at the rear), and take off the
cover (4).
∙ Unscrew the upper hinge bracket (5) and remove it.
Caution: the door must be supported while this is done.
∙ Take off the freezer door (18).
∙ Unscrew the hinge pin (7) together with the nut (6) and
washers (8), and fi t the entire assembly to the opposite side
of the hinge bracket.
∙ Undo the fi xing screws (11) on the centre hinge bracket (10)
and take them off, together with the washers (12).
Caution: Support the door.
∙ Take off the centre hinge bracket (10) together with the
hinge pin washers and the plastic plate (9).
∙ Take off the refrigerator door (13).
∙ Tilt the whole unit towards the rear.
∙ Unscrew the lower hinge bracket (14) and take it off.
∙ Unscrew the hinge pin (15) from the bracket, and re-insert it
from the other side.
∙ Remove both screws on the left of the underside and
replace them on the right.
∙ Fit the lower hinge bracket (14) on the left of the underside.
∙ Put the washers on the hinge pin.
∙ Remove the cap (19) from the freezer door and the cap (16)
from the refrigerator door and replace them on the opposite
side of the doors.
∙ Take off the caps (17) from the partition between the
refrigerator and freezer compartments and remove the
screws.
∙ Replace both screws on the opposite side and then the
caps.
∙ Fit the refrigerator door (13) onto the pin (15) of the lower
hinge bracket.
∙ Fit the pin of the centre hinge bracket (10), together with the
washers, to the refrigerator door (13).
∙ Fit the centre hinge bracket (10) together with the plastic
plate (9).
∙ Remove both screws from the upper left and replace them
on the right.
∙ Place the freezer door (18) onto the pin of the centre hinge
bracket (10).
∙ Fit the pin of the upper hinge bracket (5) to the freezer door
(18), and then fi t and secure the upper hinge bracket (5).
Note: If necessary, the alignment of the doors can be adjusted
by slightly loosening the hinge bracket screws, but remember
to tighten them afterwards.
∙ Replace the top cover (4) and use the screws (1 and 3) to
secure it (two screws at the front and two at the rear).
∙ Fit the two enclosed spacer elements (2) into the
corresponding guide slots on the rear).
If the unit has been tilted to more than 30°, wait for about 4
hours before re-connecting it to the mains.

Temperature control

The unit is re-activated by connecting it to the mains. It is only
switched off completely when the plug is removed from the wall
socket.
The temperature in the refrigerator cabinet can be adjusted by
setting the temperature control. Turning the control clockwise
will decrease the temperature, while turning it anti-clockwise
will increase it.
15