Table Des Matières; Setup - Sony Trinitron GDM-F520 Mode D'emploi

Table of Contents
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Preset mode timing table . . . . . . . . . . . . . . . . . . . . . i
TCO'99 Eco-document . . . . . . . . . . . . . Back Cover

Setup

1
Connecting your monitor to your computer
x To connect to the HD15 input connector
to HD15 video signal cable
(supplied)
x To connect to the 5 BNC connectors
R G B HD VD
to SYNC IN HD/VD
to VIDEO IN R/G/B
Connecting to a Macintosh or compatible
computer
When connecting this monitor to a Power Mac G3/G4 computer,
use the supplied adapter if necessary. Connect the supplied adapter
to the computer before connecting the cable. If you connect to
another version of Macintosh series computer, having 2 rows of
pins, you will need a different adapter (not supplied).
2
Turning on the monitor and computer
1
Connect the power cord to the monitor and press the
! (power) switch to turn on the monitor.
2
Turn on the computer.
No need for specific drivers
This monitor complies with the "DDC" Plug & Play standard and
automatically detects all the monitor's information. No specific driver
needs to be installed to the computer.
The first time you turn on your PC after connecting the monitor, the setup
Wizard may appear on the screen. In this case, follow the on-screen
instructions. The Plug & Play monitor is automatically selected so that you
can use this monitor.
Notes
• Plug and Play is compatible with the HD15 connector only, and not
compatible with the 5 BNC connectors.
• Do not touch the pins of the video signal cable connector.
• Check the alignment of the HD15 connector to prevent bending the pins
of the video signal cable connector.
to HD15 of the
connecting computer
video signal cable
(not supplied)
Refer to the preceding
examples to connect to
your computer.
â
• Trinitron is a registered trademark of Sony Corporation.
• Macintosh is a trademark licensed to Apple Computer, Inc., registered in
the U.S.A. and other countries.
â
• Windows and MS-DOS are registered trademarks of Microsoft
Corporation in the United States and other countries.
• IBM PC/AT and VGA are registered trademarks of IBM Corporation of
the U.S.A.
ä
• VESA and DDC are trademarks of the Video Electronics Standard
Association.
E S
• NERGY TAR is a U.S. registered mark.
• All other product names mentioned herein may be the trademarks or
registered trademarks of their respective companies.
• Furthermore, " ä " and " â " are not mentioned in each case in this manual.
To select the input signal
You can connect two computers to this monitor using the HD15 and
BNC connectors. To select one of the two computers, use the
INPUT switch. The selected connector appears on the screen for 3
seconds.
Note
If no signal is input to the selected connector, NO SIGNAL appears on the
screen. After a few seconds, the monitor enters the power saving mode. If
this happens, switch to the other connector.
To connect Universal Serial Bus (USB) compliant
peripherals
Confirm that the monitor and computer are turned on, then
connect your computer to the USB connectors (
of the monitor.
Connect your computer to the square upstream
connector using the supplied USB cable.
( )
If a Windows message appears, follow the on-screen instructions
and select "Generic USB Hub".
When connecting your USB compliant peripheral devices (e.g.,
printer, keyboard, mouse, scanner, etc.) connect the rectangular
downstream USB connector
(
Note
The monitor functions as a USB hub as long as the monitor is either "on" or
in power saving mode.
HD15 input connectors
Pin No. Signal
1 Red
2 Green (Sync on
Green)
3 Blue
4 ID (Ground)
5 DDC Ground*
6 Red Ground
7 Green Ground
8 Blue Ground
* DDC (Display Data Channel) is a standard of VESA.
) on the right side
.
)
5 4 3 2 1
10 9 8 7 6
15 14 13 12 11
Pin No. Signal
9 DDC + 5V*
10 Ground
11 ID (Ground)
12 Bi-Directional
Data (SDA)*
13 H. Sync
14 V. Sync
15 Data Clock
(SCL)*
3
US