Room Temperature Adjustment; Fan Speed Adjustment; Ventilation; Others - Mitsubishi Electric City Multi PEFY-P06NMAU-E2 Manuel D'utilisation

For fan
Press the 3 [Mode (BACK)] Button and bring up the "
• The fan operation functions to circulate the air in the room.
• The temperature of the room cannot be set by fan operation.
Caution:
Never expose your body directly to cool air for a long time. Excessive expo-
sure to cool air is bad for your health, and should therefore be avoided.
Dry operation
The dry is a microcomputer-controlled dehumidifying operation which controls
excessive air-cooling according to the room temperature of your choice. (Not us-
able for heating.)
1. Until reaching room temperature of your choice
The compressor and indoor fan function is linked motion according to the
change of the room temperature and automatically repeat ON/OFF.
2. When reaching room temperature of your choice
Both the compressor and indoor fan stop.
When stop continues for 10 minutes, the compressor and indoor fan are oper-
ated for 3 minutes to keep the humidity low.
For heating
Press the 3 [Mode (BACK)] Button to bring up the "
Regarding displays during heating operation "DEFROST"
Displayed only during the defrosting operation.
"STAND BY"
Displayed from the start of heating operation until the moment warm air blows out.
Caution:
• When the air-conditioner is used together with burners, thoroughly venti-
late the area. Insuffi cient ventilation can result in accidents due to oxygen
defi ciency.
• Never place a burner at a place where it is exposed to the airfl ow from
the air-conditioner.
Doing so can result in imperfect combustion of the burner.
• The microcomputer functions in the following cases:
• Air does not blow out when heating starts.
- To prevent any cool air from escaping, the indoor fan is gradually switched in
sequence from faint airfl ow/weak airfl ow/set airfl ow according to the temperature
rise of the blown out air. Wait a moment until the airfl ow comes out naturally.
• The fan is not moving at the set speed.
- In some models, the system switches over to faint airfl ow when the temper-
ature of the room reaches the set temperature. In other cases, it stops to
prevent any cool air from escaping during the defrosting operation.
• Air fl ows out even if operation is stopped.
- Approximately 1 minute after the stop of operation, the indoor fan sometimes
rotates to eliminate extra heat generated by the electric heater, etc.
The fan speed comes to low or high.

4. The smart way to use

Even minimal steps to care for your air conditioner can help make its use far
more effective in terms of air-conditioning effect, electricity charges, etc.
Set the right room temperature
• In cooling operation, a temperature difference of about 5 °C [9 °F] between
indoors and outdoors is optimum.
• If the room temperature is raised by 1 °C [2 °F] during air-cooling operation,
about 10 % electric power can be saved.
• Excessive cooling is bad for health. It also results in the waste of electric power.
Clean the fi lter thoroughly
• If the screen of the air fi lter becomes clogged, the airfl ow and air-conditioning
effect can be signifi cantly reduced.
Further, if the condition is left unattended, failure can result. It is particularly
important to clean the fi lter at the beginning of the cooling and heating seasons.
(When profuse dust and dirt have accumulated, clean the fi lter thoroughly.)

3.3. Room temperature adjustment

FAN" display.
To change room temperature
Press the 1 [Set Temperature] Button and set the room temperature of your
choice.
Pressing
If the pressing is continued, the setting continues to change by 1 °C [2 °F].
• Indoor temperature can be set within the following range.
• Temperature cannot be set for the fan mode.
* The range of room temperature display is 8 °C [46 °F] - 39 °C [102 °F]. Outside
this range, the display fl ashes either 8 °C [46 °F] - 39 °C [102 °F] to inform you
if the room temperature is lower or higher than the displayed temperature.

3.4. Fan speed adjustment

To change fan speed
Every time you press the 6 [Fan Speed] button once, it switches from the low-speed
to high-speed settings successively.
In the electronics dry operation, the indoor fan automatically turns to low-speed
operation. Switching of fan speed is impossible. (Only the display on the remote
HEAT" display.
controller changes.)
* Every time the fan speed adjustment button is pressed once, the fan speed is changed.
Fan speed : 3 stages
Display:
* This setting can be adjusted only with MA remote controller.

3.5. Ventilation

• The ventilation unit (OA processing unit or LOSSNAY) automatically goes into
operation when the indoor unit that is interlocked with it goes into operation.
If the 8 [Ventilation] button is pressed while the indoor unit is stopped, only
•
the ventilator goes into operation.
• Press the 8 [Ventilation] button to change the fan speed.
• Depending on the models, the indoor unit fan goes into operation while the unit
is in the ventilation mode.

3.6. Others

NOT AVAILABLE
Prevent intrusion of heat during air-cooling
• To prevent the intrusion of heat during cooling operation, provide a curtain or a
blind on the window to block out direct sunlight. Also, do not open the entrance
or exit except in cases of dire necessity.
Carry out ventilation sometimes
• Since the air periodically gets dirty in a room that is kept closed for a long time,
ventilation is sometimes necessary. When gas appliances are used together
with the air conditioner, special precautions must be taken. If the "LOSSNAY"
ventilation unit developed by our company is used, you can perform ventilation
with less waste. For details on this unit, consult with your dealer.
or once changes the setting by 1 °C/1 °F .
Cooling/dry :19 °C [67 °F] - 30 °C [87 °F]
Heating :17 °C [63 °F] - 28 °C [83 °F]
(Low) (Mid)
: Displayed when control is executed by a separately
sold centralized control unit, etc.
STAND BY
: Displayed from the start of heating operation until the
DEFROST
moment warm air blows out.
CHECK
: This displays indication when some abnormality oc-
curs in the unit.
: When a Button is pressed for any function which
the indoor unit cannot perform, this display fl ashes
concurrently with the display of that function.
: In the system in which the [Sensor] display is indi-
cated as the "remote controller", room temperature
measurement is performed by the room temperature
sensor built into the remote controller.
FILTER
: Displayed when it is time to clean the fi lter.
Press the A [FILTER ( )] Button twice, then the display
is disappeared.
(High) (AUTO*)
7