Bosch PWS 700-115 Notice Originale page 18

OBJ_DOKU-28019-001.fm Page 18 Friday, September 23, 2011 8:28 AM
18 | English
Technical Data
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Engineering Director
Engineering PT/ESI
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
01.09.2011
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance (for addresses, see section
„After-sales Service and Customer Assistance".
2 609 005 556 | (23.9.11)
PWS ... 700-115 720-115 720-125 750-115 750-125
3 603 ... A64 2.. A64 0..
W 705 720
W 380 360
-1
min 11000 11000
mm 115 115
M 14 M 14
mm 21 21
kg 1.9 1.9
/II /II
Protection Guard for Grinding
of the work process. For this, press the release lever 1 up-
ward and turn the protection guard 6 to the required position.
Always adjust the protection guard 6 in such a manner
that all 3 red cams of release lever 1 engage into the
corresponding notches of the protection guard 6.
Adjust the protection guard 6 in such a manner that
sparking is prevented in the direction of the operator.
The protection guard 6 may be turned only upon actua-
tion of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
Note: The encoding keys on the protection guard 6 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 10.
Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 10 is mounted in the same
manner as the protection guard for grinding 6.
A64 0.. A64 1.. A64 1..
720 750 750
360 450 450
11000 11000 11000
125 115 125
M 14 M 14 M 14
21 21 21
1.9 1.9 1.9
/II /II /II
Place the protection guard 6 onto
the spindle collar of the machine
until the encoding keys of the pro-
tection guard agree with the spin-
dle collar. Press and hold the re-
lease lever 1 while doing this.
Press the protection guard 6 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protec-
tion guard 6 to the requirements
Bosch Power Tools