Low Emission Fire Lighting; Normal Operation; Use Of The Oven (If Present) - Nordica TERMOSUPREMA Compact-DSA Manuel Utilisateur

LOW EMIssION FIRE LIgHTINg

smokeless combustion is a way of lighting a fire able to significantly reduce the emission of harmful substances. The wood burns gradually
from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the flame and
therefore burn almost completely.
place the logs in the hearth a certain distance apart as shown in the
or vertically in the case of tall narrow combustion chambers. place the fire starter module on top of the pile, arranging the first logs in the
module at right angles to the pile of wood.
Fire sTARTER MODULE. This fire starter module replaces a paper or cardboard starter.
prepare four logs, 20 cm long with a cross section of 3 cm by 3 cm. Cross the four logs and place them on top of the pile of wood at right
angles, with the fire lighter (wax impregnated wood fibre for example) in the middle. The fire can be lit with a match. if you want, you can
use thinner pieces of wood. in this case, you will need a larger quantity.
keep the flue gas exhaust valve and combustion air regulator open.
after lighting the fire, leave the combustion air regulator open in the position shown:
FUEL
Wood
IMPORTANT:
• do not add further wood between one complete load and the next;
• do not suffocate the fire by closing the air intakes;
• regular cleaning by a chimney sweep reduces fine particle emissions.
• These instructions are backed by eneRGia Legno sVizzeRa

NORMAL OPERATION

IMPORTANT: For safety reasons the door of the hearth can be opened only for the loading of the fuel. The hearth door must
always remain closed during operation or rest.
after having positioned the registers correctly, insert the indicated hourly wood load avoiding overloads that cause anomalous stresses and
deformations. You should always use the product with the door closed in order to avoid damages due to overheating (forge effect).
The inobservance of this rule makes the warranty expire.
for safety reasons the door of the appliances with constructive system 1, must be opened only for the loading of the fuel or for removing the
ashes, while during the operation and the rest, the door of the hearth must remain closed.
The appliances with constructive system 2 must be connected to their own flue. The operating with open door is allowed under supervision.
With the controls positioned on the front of the appliance it is possible to adjust the heat emission of the hearth. They have to be opened
according to the calorific need. The best combustion (with minimum emissions) is reached when, by loading the wood, most part of the air for
combustion flows through the secondary air register.
Never overload the appliance (see the hourly wood load in the table here below). Too much fuel and too much air for the combustion may
cause overheating and then damage the stove. You should always use the appliance with the door closed in order to avoid damages due to
overheating (forge effect). The inobservance of this rule makes the warranty expire.
The adjustment of the registers necessary to reach the rated calorific yield with a depression at the stack of 12 pa (1,2 mm of column of water)
is the following one: see chapter TeCHniCaL desCRipTion. The appliance works as an intermittent operating appliance.
In the event that the water temperature exceeds the tripping temperature of the safety devices, immediately suspend the
feeding of wood, and make sure that the water temperature and the flame decrease, eliminating the causes of the
overheating (if necessary by closing the air register).
If the water system is connected in the appliance, the hot water tap can be opened to speed up the cooling of the appliance.
Besides the adjustment of the air for the combustion, the intensity of the combustion and consequently the thermal performance
of the device is influenced by the stack. a good draught of the stack requires a stricter adjustment of air for combustion, while a poor draught
requires a more precise adjustment of air for combustion.
To verify the good combustion, check whether the smoke coming out from the stack is transparent.
if it is white, it means that the device is not properly adjusted or the wood is too wet; if instead the smoke is gray or black, it signals that the
combustion is not complete (it is necessary a greater quantity of secondary air).
WARNINg: When fuel is added onto the embers in the absence of a flame, a considerable amount of fumes may develop. should
this happen, an explosive mixture of gas and air may form, and in extreme cases an explosion may occur. for safety reasons it is
advisable to perform a new lighting procedure with the use of small strips.

UsE OF THE OVEN (IF PREsENT)

place the smoke controller in the position Use of THe oVen (see chap. TeCHniCaL desCRipTion)
Thanks to the air flow for the combustion, the temperature of the oven may become remarkably affected. a sufficient flue of the chimney and
of the channels, well cleaned for the flow of burning smokes around the oven are fundamental for a good cooking result. The oven pan may
be located on different plans. Thick cakes and big roasts must be introduced in the lowest level. flat cakes and biscuits must reach the medium
level. The upper level may be used to heat or grill.
The oven pan and the chrome plated oven grille may be located on different plans (see chapter Technical description - aCCessoRies).
Picture
PRIMARY Air
open
www.energia-legno.ch
ENgLIsH
7. arrange the largest at the bottom and the smallest at the top,
sECONDARY Air
open
TERTIARY air
5
33