Publicité

Liens rapides

OWNER / OPERATOR MANUAL
MODE D'EMPLOI
MANUAL DE INSTRUCCIONES
WARNING
The engine exhaust from
this product contains
chemicals known to the
State of California to cause
cancer, birth defects or
other reproductive harm.
WARNING
Before using our
product, please read this
manual carefully to
understand the proper use
of your unit.
APPLICABLE SERIAL NUMBERS :
793480 and up
AVERTISSEMENT
Les échappements du
moteur de ce produit
contiennent des produits
chimiques connus par l'Etat
de Californie comme étant
responsables de cancers,
d'anomalies congénitales et
d'autres atteintes à
l'appareil reproducteur.
AVERTISSEMENT
Avant d'utiliser cette
produits, veuillez lire
attentivement ce manuel
afin de bien comprendre le
bon fonctionnement de cet
appareil.
NUMEROS DE SERIE APPLICABLES :
793480 et au-delà
CHAINSAW
TRONÇONEUSES
MOTOSIERRAS
G3800AVS
ADVERTENCIA
Los gases de escape del
motor de este producto
contienen sustancias
químicas conocidas por el
Estado de California como
causantes de cáncer,
malformaciones en recién
nacidos y otros problemas
de reproducción.
ADVERTENCIA
Antes de usar nuestros
productos, lea
detenidamente este manual
a fin de familiarizarse con el
uso correcto de este
aparato.
NÚMEROS DE SERIE APLICABLES:
793480 y superior
T2108-93112 (711)

Publicité

Table des Matières
loading

Sommaire des Matières pour RedMax G3800AVS

  • Page 1 T2108-93112 (711) OWNER / OPERATOR MANUAL MODE D’EMPLOI MANUAL DE INSTRUCCIONES CHAINSAW TRONÇONEUSES MOTOSIERRAS G3800AVS WARNING AVERTISSEMENT ADVERTENCIA Les échappements du Los gases de escape del The engine exhaust from moteur de ce produit motor de este producto this product contains...
  • Page 2 English SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
  • Page 3: Table Des Matières

    Français Español SECURITE LA SEGURIDAD PRIMERO Les instructions contenues dans les mises en Las instrucciones que aparecen en este manual garde de ce mode d’emploi portant le symbole bajo las advertencias marcadas con el símbolo concernent les points critiques qui doivent être hacen referencia a puntos críticos que deben pris en considération pour éviter les blessures tomarse en consideración para evitar posibles...
  • Page 4 Power unit : Displacement ·············································································································· 2.34(37.2) cu-in(cm Fuel ······································································································ Mixture (Gasoline 50 : 2-cycle oil 1) (when using RedMax/ZENOAH genuine oil) Fuel tank capacity ··········································································································· 10.4(0.31) fl.oz( ) Chain oil ·················································································································· Motor oil SAE #10W-30 Oil tank capacity ············································································································· 7.10(0.21) fl.oz( ) Carburetor ·····································································································...
  • Page 5: Emplacement Des Pieces

    Groupe moteur : Cylindrée (cm ) : ······································································································································37,2 Carburant : ········································································ Mélange (Essence/Huile moteur 2-temps : 50/1) (Lors de l’utilisation de la véritable huile RedMax/ZENOAH) Contenance du réservoir de carburant (cm ) : ·························································································310 Huile de chaîne : ································································································Huile moteur SAE# 10W-30 Contenance du réservoir d’huile (cm...
  • Page 6 English 3. Warning labels on the machine (1) Read operator's instruction book before operating this machine. (2) Wear head, eye and ear protection. (3) Use the chain saw with two hands. (4) Warning! Danger of kickback. (5) Read, understand and follow all warnings.
  • Page 7: Etiquettes D'avertissement Sur La Machine

    Français Español 3. Etiquettes d’avertissement sur la machine 3. Etiqueta de advertencia en la máquina (1) Lire le manuel avant d’utiliser cette machine. (1) Antes de utilizar esta máquina, leer el manual del operador. (2) Porter casque, lunettes de protection et (2) Llevar casco, gafas y auriculares de protección.
  • Page 8 English 4. Symbols on the machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. (a) The port to refuel “MIX GASOLINE” Position: Fuel cap (b) The port to top up chain oil Position: Oil cap (c) Setting the switch to the “O”...
  • Page 9: Symboles Utilises Sur La Machine

    Français Español 4. Symboles utilises sur la machine 4. Símbolos presentes en la máquina Pour une utilisation et un entretien sûrs, Para un uso y mantenimiento seguros les symboles sont gravés en relief sur la se han grabado en relieve los machine.
  • Page 10 English 5. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2.
  • Page 11: Consignes De Securite

    Français Español 5. Consignes de securite 5. Instrucciones de seguridad 1. Ne jamais utiliser une tronçonneuse lorsqu’on est 1. Nunca opere la motosierra cuando esté fatigado, fatigué, malade, énervé, sous l’influence de enfermo o irritado, ni cuando esté bajo la influencia médicaments entraînant vertige ou somnolence, ou de medicamentos que pueden causar somnolencia, encore sous I’influence de l’alcool ou de drogues.
  • Page 12 English 5. For safe operation 9. Never start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree. 10. Always hold the chain saw firmly with both hands when the engine is running. Use a firm grip with thumb and fingers encircling the chain saw handles.
  • Page 13 Français Español 5. Consignes de securite 5. Instrucciones de seguridad 9. Avant de commencer à tronçonner, dégager le lieu 9. Nunca comience a cortar antes de tener un área de de travail, prévoir une voie de retraite pour le trabajo despejada, un buen apoyo para los pies y moment où...
  • Page 14 English 5. For safe operation 16. Always shut off the engine before setting it down. 17. Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance.
  • Page 15 Français Español 5. Consignes de securite 5. Instrucciones de seguridad 16. Toujours arrêter le moteur avant de poser la 16. Asegúrese de apagar el motor antes de bajar la tronçonneuse. motosierra. 17. Observer la plus grande prudence en coupant les 17.
  • Page 16 English 5. For safe operation into your saw. As a chain saw user you should take several steps to keep cutting jobs free from accident or injury. (1) With a basic understanding of kickback you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents.
  • Page 17 Français Español 5. Consignes de securite 5. Instrucciones de seguridad • Les dispositifs de sécurité dont est équipée la la motosierra y puede resultar severamente lesionado. tronçonneuse ne dispensent pas d’observer la plus grande prudence. Pour éviter tout accident ou •...
  • Page 18 English 6. Installing guide bar and saw chain ■ A standard saw unit package contains the items as illustrated. (F1) (1) Power unit (2) Guide bar (3) Saw chain (4) Plug wrench (5) Screwdriver for carburetor adjustment Open the box and install the guide bar and the saw chain on the power unit as follows: WARNING The saw chain has very sharp edges.
  • Page 19: Montage Du Guide-Chaîne Et De La Chaîne

    Français Español 6. Montage du guide-chaîne et de la chaîne 6. Instalación de la barra guía y de la cadena de la motosierra ■ Contenu de I’emballage de la tronçonneuse. (F1) ■ El paquete estándar de la motosierra contiene los elementos indicados en la ilustración. (F1) (1) Groupe moteur (2) Guide-chaîne (1) Unidad de potencia...
  • Page 20 English 6. Installing guide bar and saw chain NOTE A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itseif and the guide bar.
  • Page 21 Français Español 6. Montage du guide-chaîne et de la chaîne 6. Instalación de la barra guía y de la cadena de la motosierra (3) Serrer (2) Aflojar (4) Vis du tendeur (3) Tensar (5) Soulever (4) Tornillo del tensor (5) Levante REMARQUE NOTA Lorsqu’elle est neuve, Ia chaîne a tendance à...
  • Page 22 • The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti- oxidant added quality oil expressly labeled for air- cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE) •...
  • Page 23: Carburant Et Huile De Chaîne

    • Les moteurs RedMax sont lubrifiés à l’aide d’une • Los motores de RedMax están lubricados con un huile spécialement conçue pour les moteurs 2 temps aceite especialmente formulado para uso en à...
  • Page 24 English 7. Fuel and chain oil ■ HOW TO MIX FUEL IMPORTANT Agitate carefully. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. 3. Pour in all of the oil and agitate well. 4.
  • Page 25 Français Español 7. Carburant et huile de chaîne 7. Combustible y aceite de la cadena participer ainsi à la protection de l’environnement et • Gasolinas o aceites de mala calidad puede dañar de votre santé. los anillos de sellado, las líneas o el tanque de •...
  • Page 26 English 7. Fuel and chain oil FOR YOUR ENGINE LIFE, AVOID; 1. FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly. 2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.
  • Page 27 Français Español 7. Carburant et huile de chaîne 7. Combustible y aceite de la cadena A EVITER POUR PROLONGER LA DUREE DE VIE PARA CONTRIBUIR A LA VIDA ÚTIL DEL MOTOR, DU MOTEUR; EVITE; 1. ESSENCE SANS HUILE (ESSENCE PURE) – 1.
  • Page 28 English 8. Operation WARNING It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. Before starting engine, make sure that all the parts including bar and chain are installed properly. ■ STARTING THE ENGINE 1.
  • Page 29: Fonctionnement

    Français Español 8. Fonctionnement 8. Uso AVERTISSEMENT ADVERTENCIA Il est dangereux d’utiliser une scie avec des pièces Es muy peligroso operar una sierra de cadena cassées ou manquantes. cuando sus componentes están averiados o Avant de mettre le moteur en marche, toujours faltantes.
  • Page 30 English 8. Operation 5. When engine has ignited, first push in the choke knob to the first-stage position and then pull the starter again to start the engine. 6. Allow the engine to warm up with the throttle lever pulled slightly. WARNING Keep clear of the saw chain as it will start rotatIng upon starting of engine.
  • Page 31 Français Español 8. Fonctionnement 8. Uso 5. Si le moteur démarre et cale, repousser le bouton motosierra puede tocar su cuerpo. de starter à la première position et tirer à nouveau la cordelette du lanceur pour remettre le moteur en 5.
  • Page 32 English 8. Operation 1. H and L needles are restricted within the number of turn as shown below. H needle –1/4 L needle fixed 2. Start the engine and allow it to warm up in low speed for a few minutes. 3.
  • Page 33 Français Español 8. Fonctionnement 8. Uso 1. Le nombre de tour des pointeaux H et L est limité de 1. Las agujas H y L (alta y baja) están restringidas en la manière suivante. número de vueltas, como se indica abajo. Pointeau H –1/4 Aguja H –1/4 Pointeau L fixé...
  • Page 34 English 8. Operation immediately release your fingers from the throttle lever and stop the engine. ■ STOPPING THE ENGINE 1. Release the throttle lever to allow the engine to idle for a few minutes. 2. Set the switch to the “O” (STOP) position. (F17) (1) Switch Carburetor anti-freeze mechanism Operating the chain saws in temperatures of 0–5°C at...
  • Page 35 Français Español 8. Fonctionnement 8. Uso entraîne des causes de pannes. freno aplicado, puesto que eso resulta en Lorsque le frein s’applique accidentellement pendant le sobrecalentamiento del embrague y avería del fonctionnement, dégager le doigt du papillon aparato. immédiatement pour arrêter le moteur. Cuando el freno funciona durante la operación de la sierra, soltar inmediatamente la palanca del acelerador y parar el motor.
  • Page 36 English 8. Operation ■ HOW TO SWITCH BETWEEN OPERATING MODES (F19) 1. Flip the engine switch to turn off the engine. 2. Remove the cover to the air filter, remove the air filter, and then remove the choke knob from the cylinder cover.
  • Page 37 Français Español 8. Fonctionnement 8. Uso ■ COMMENT CHANGER ENTRE LES MODES ■ CÓMO CAMBIAR DE MODO DE OPERACIÓN D’UTILISATION (F19) (F19) 1. Désenclencher le commutateur de moteur pour 1. Mueva el interruptor del motor para apagar el motor. couper le moteur. 2.
  • Page 38 English 9. Sawing WARNING • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • Always follow the safety regulations. The chain saw must only be used for cutting wood.
  • Page 39: Travail À La Tronçonneuse

    Français Español 9. Travail à la tronçonneuse 9. Utilización de la motosierra AVERTISSEMENT ADVERTENCIA • Avant de commencer à travailler, Iire • Antes de comenzar la tarea, Iea atentamente la attentivement le chapitre “Pour la sécurité” au sección “Para una operación segura”. Se reco- début de cette notice.
  • Page 40 English 9. Sawing ■ FELLING A TREE (F22) 1. Decide the felling direction considering the wind, lean of the tree, location of heavy branches, ease of job after felling and other factors. 2. While clearing the area around the tree, arrange a good foothold and retreat path.
  • Page 41 Français Español 9. Travail à la tronçonneuse 9. Utilización de la motosierra ■ Abattage d’un arbre (F22) ■ TALADO DE ÁRBOLES (F22) 1. Déterminer le sens dans lequel I’arbre doit choir, 1. Decida la dirección en la cual hará caer el árbol, compte tenu du vent, de l’inclinaison du tronc, de la teniendo en cuenta la dirección del viento, la disposition des branches les plus lourdes, de la...
  • Page 42 English 9. Sawing A Log hanging off the ground (F24) In area A, saw up from the bottom one-third and finish by sawing down from the top. In area B, saw down from the top one-third and finish by sawing up from the bottom.
  • Page 43 Français Español 9. Travail à la tronçonneuse 9. Utilización de la motosierra Tronc en surélévation (F24) Un tronco separado del suelo (F24) Commencer par couper au tiers par en dessous dans En el área “A”, comience cortando desde abajo hasta la zone A et finir la coupe par-dessus.
  • Page 44 English 10. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. WARNING Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting.
  • Page 45: Entretien

    Français Español 10. Entretien 10. Maintenimiento L’entretien, le remplacement ou la réparation du El mantenimiento, recambio o reparación del dispositif et des systèmes de lutte contre les dispositivo de control de emisiones y del equipo émissions peuvent être effectués par toute société pueden realizarse en cualquier centro de ou individu spécialisé...
  • Page 46 English 10. Maintenance ■ PERIODICAL SERVICE POINTS 1. Cylinder fins Dust clogging between the cylinder fins will cause overheating of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover. When installing the cylinder cover, make sure that switch wires and grommets are positioned correctly in place.
  • Page 47 Français Español 10. Entretien 10. Maintenimiento ■ ENTRETIEN PERIODIQUE ■ PUNTOS DE SERVICIO PERÍODICO 1. Ailettes de refroidissement du cylindre 1. Aletas del cilindro Si de la poussière reste entre les ailettes du cylindre, le El polvo entre las aletas del cilindro causará el moteur va chauffer.
  • Page 48 English 11. Maintenance of Saw Chain and Guide Bar ■ Saw Chain WARNING It is very important for smooth and safe operation to keep the cutters always sharp. The cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. •...
  • Page 49: Entretien De La Chaîne Et Du Guide-Chaîne

    Français Español 11. Entretien de la chaîne et du guide-chaîne 11. Mantenimiento de la cadena de la motosierra y de la barra guía ■ Chaîne ■ Cadena de la motosierra AVERTISSEMENT ADVERTENCIA Pour la sécurité et le rendement dans le travail, les motivos seguridad para...
  • Page 50 English 11. Maintenance of Saw Chain and Guide Bar Make sure every cutter has the same length and edge angles as illustrated. (F38) (4) Cutter length (5) Filing angle (6) Side plate angle (7) Top plate cutting angle ■ GUIDE BAR •...
  • Page 51 Français Español 11. Entretien de la chaîne et du guide-chaîne 11. Mantenimiento de la cadena de la motosierra y de la barra guía Vérifier que toutes les dents présentent les longueurs Verifique que el largo y el ángulo del borde de todos et angles de tranchant indiqués sur l’illustration.
  • Page 52 English 12. Troubleshooting Guide Case 1. Starting failure WARNING Make sure the icing prevention system is not working. Check fuel for water Replace with proper ➜ or substandard mix- fuel. ture. Remove and dry the Check for engine spark plug. ➜...
  • Page 53: Guide De Dépannage

    Français Español 12. Guide de dépannage 12. Guía para la localización de averías Cas 1. Défaut de démarrage Caso 1. Falla de arranque AVERTISSEMENT ADVERTENCIA Veiller à ce que le système de prévention contre la Compruebe que el sistema de prevención de congélation ne soit pas en fonctionnement.
  • Page 54: Rangement

    English 13. Storage • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.
  • Page 55: Liste Des Pièces

    RedMax/ZENOAH replacement. en la lista de piezas. comme précisé dans la liste 2. RedMax/ZENOAH does not 2. RedMax/ZENOAH no garantiza des pièces. warrant the machines, which máquinas que se han dañado 2. RedMax/ZENOAH ne garantit...
  • Page 56 G3800AVS 15. Parts list Fig.1 POWER UNIT (S/N 793480 and up)
  • Page 57 G3800AVS Fig.1 POWER UNIT (S/N 793480 and up) Q'TY Q'TY Key# PART NUMBER DESCRIPTION NOTE Key# PART NUMBER DESCRIPTION NOTE /UNIT /UNIT 2898-12111 Cylinder 848-C40-5121 Clutch ass’y 2867-14110 Insulator 2870-51230 • Spring 2850-14123 Gasket, inlet 2850-51211 Plate 3330-14121 Gasket, carb...
  • Page 58 G3800AVS 15. Parts list Fig.2 POWER UNIT (S/N 793480 and up)
  • Page 59 G3800AVS Fig.2 POWER UNIT (S/N 793480 and up) Q'TY Q'TY Key# PART NUMBER DESCRIPTION NOTE Key# PART NUMBER DESCRIPTION NOTE /UNIT /UNIT T2100-32110 Left handle 2872-54230 • Spring 848-825-7211 Screw TP5x27 2851-54260 • Stopper plate T2100-33000 Right handle ass’y 2851-54270 •...
  • Page 60 G3800AVS 14. Parts list Fig.3 CARBBURETOR COMPONENTS (S/N 793480 and up) Q'TY Q'TY Key# PART NUMBER DESCRIPTION NOTE Key# PART NUMBER DESCRIPTION NOTE /UNIT /UNIT T2108-81001 CARBURETOR ASS'Y –––––––––– • • SCREEN – 2850-81120 • PUMP COVER –––––––––– • • VALVE, inlet –...
  • Page 61 G3800AVS 13. Parts list Fig.4 ACCESSORIES (S/N 793480 and up) Q'TY Q'TY Key# PART NUMBER DESCRIPTION NOTE Key# PART NUMBER DESCRIPTION NOTE /UNIT /UNIT 3320-91140 Plug 13x19 (OP) 2670-91150 Driver (OP) Oregon 10014 Bar 16” Oregon double- Chain guard 91VG56X...
  • Page 62 AMERICA, INC. AT (770)-381-5147. IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL OUT THE CARD AND SEND IT TO RedMax / ZENOAH AMERICA WITHIN SEVEN (7) DAYS. BE SURE TO KEEP A COPY FOR YOUR RECORDS.
  • Page 63 INC. au (770)-381-5147 Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et l'adresser à RedMax / ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie pour vous. ZENOAH AMERICA, INC.
  • Page 64 ZENOAH AMERICA, INC. LLAMANDO AL (770)-381-5147. IMPORTANTE: RECIBIRÁ UNA TARJETA DE REGISTRO DE GARANTÍA EN EL MOMENTO DE LA COMPRA. LLENE LA TARJETA Y ENVÍELA A RedMax / ZENOAH AMERICA DENTRO DE SIETE (7) DÍAS. ASEGÚRESE DE CONSERVAR UNA COPIA PARA SUS REGISTROS.

Table des Matières