SOLIS 8324 Mode D'emploi page 35

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

s BLENDING WITH THE BLENDER JUG
1. Place the blender jug on the motor base in an upright position.
2. Place the foods or liquids in the blender jug and make sure that the ingredients
do not exceed the MAX marking (1,5 litres). Place the lid firmly on the jug so
that it is properly sealed all around. Place the measuring cap in the centre of the
lid and screw it shut in a clockwise direction until it locks into place in the lid.
Note: If you want to add oil or other liquids during blending, please remove
the measuring cap and pour the ingredients into the jug through this opening
in the lid. This only works if the volume of the blended ingredients lies under
the MAX marking. The lid itself must never be removed from the jug during the
blending process.
3. Plug the power plug into a suitable power outlet.
4. Set the turn-switch to one of the desired speeds. Select the PULSE position if
the processed food is very thick or coarse to allow it to circulate in the jug.
Note: Do not fill the blender jug above the MAX marking! Should the jug be
filled in such a way that the contents reach almost or exactly up to the MAX
marking, place a hand on the lid to prevent it from spilling out during use.
5. Once the blending process is finished, turn the turn-switch back to OFF and
pull the power plug from the socket with dry hands. Wait for the motor and
the blades to come to a complete standstill before removing the blender jug
resp. the lid. To remove, pull the blender jug up without turning it. Only lift the
blender jug off when the motor and the blades have come to complete stand-
still.
The blender always has to be unplugged when it is not in use or before it is
disassembled, cleaned or stored.
68
s TIPS FOR PERFECT BLENDING IN THE
BLENDER JUG
Should the volume be under the MAX marking during operation, the measuring
cap in the lid can be removed so that oil or other liquids can be added.
Be careful when blending large amounts or liquids – the mixture might spill out
through the measuring cap opening in the lid of the jug!
The blender should only be used until foods or mixing program are ready and
form the perfect final product. Do not blend foods longer than necessary!
Use the PULSE function when the foods are too thick or coarse to circulate in
the blender jug
Never exceed the MAX marking when filling the blender jug with foods and
liquids.
Ingredients might stick the side of the jug. To move the foods back towards the
blades, turn the blender off and pull the plug. Wait for the blades to come to
a full stop. Remove the lid. Push the foods downwards with a plastic spatula,
pushing from the side of the jug towards the blades. After that, firmly place
the lid back on the jug, connect the plug, activate the appliance and continue
blending.
Should you notice moisture or liquid on the upper part of the motor base dur-
ing blending, immediately switch the appliance off with the turn-switch (OFF
position) and pull the plug. Wait for the blades to come to a full stop. Lift the
blender jug off and immediately wipe the motor base dry with a dry cloth or
kitchen towel.
You can adjust resp. change the speed during the blending process. Turn the
turn-switch to a different speed and the blender will immediately change to this
new speed.
Use the speeds BLEND or LIQUIFY to turn fruit, ice cream and yoghurts into thick
smoothies, cremes or milkshakes.
Use the PULSE function for foods that require individual, powerful bursts of
blending, f.e. when chopping nuts or crushing ice cubes.
You blender can crush a maximum of 8 standard tray ice cubes in the blender
jug. Use the PULSE function.
When preparing drinks with ice cubes or frozen fruit, you should engage the
PULSE function multiple times.
Alternating between the PULSE function and another speed setting will deliver
optimal results when blending and chopping foods.
69

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mix & go

Table des Matières