Bosch GWS 24-230 JVX Professional Notice Originale page 22

22 | English
Switch without locking mechanism (country-specific):
To start the power tool, push the on/off switch (3) forwards
and then press it down.
To switch off the power tool, release the on/off switch (3).
Always check abrasive tools before using them. The
u
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.
Run-out brake
The power tool is fitted with the Bosch Brake
System, a patented electromechanical run-out
brake. When the power supply is switched off
or interrupted, the abrasive tool is brought to a
complete stop within a few seconds. This
means that the run-out time is 70% shorter than for angle
grinders without a run-out brake and enables the power tool
to be set down sooner.
Note: If the braking effect deteriorates noticeably, the run-
out brake has failed. The power tool must be sent to the
after-sales service immediately; see the "After-Sales Service
and Application Service" section for addresses.
Restart protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (3) to the off posi-
tion and then switch the power tool on again.
Starting current limitation
The electronic starting current limitation feature restricts the
power of the power tool when it is switched on and enables
operation using a 16 A fuse.
Note: If the power tool runs at full speed immediately after
being switched on, this means that the starting current limit-
ation and restarting protection mechanisms have failed. The
power tool must be sent to the after-sales service immedi-
ately; see the "After-Sales Service and Application Service"
section for addresses.
Working advice
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Exercise caution when cutting slots in structural walls;
u
see the "Information on structural design" section.
Clamp the workpiece if it is not secure under its own
u
weight.
Do not load the power tool so heavily that it comes to a
u
stop.
If the power tool has been subjected to a heavy load,
u
continue to run it at no-load for several minutes to
cool down the accessory.
Do not use the power tool with a cut-off stand.
u
1 609 92A 5FF | (11.02.2020)
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Note: Remove the plug from the socket when not using the
tool. When the power tool is plugged in, mains voltage is
present and the tool consumes a small amount of electricity,
even if switched off.
Rough grinding
Never use cutting discs for rough grinding.
u
The best rough grinding results are achieved with a set angle
of 30° to 40°. Move the power tool back and forth with mod-
erate pressure. This will ensure that the workpiece does not
become too hot or discolour and that grooves are not
formed.
Flap Disc
With the flap disc (accessory), curved surfaces and profiles
can be worked. Flap discs have a considerably higher ser-
vice life, lower noise levels and lower sanding temperatures
than conventional sanding sheets.
Cutting Metal
Always use the protective guard for cutting (14) when
u
cutting bonded abrasives.
When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
Cutting stone
Provide sufficient dust extraction when cutting stone.
u
Wear a dust mask.
u
The power tool may be used only for dry cutting/grind-
u
ing.
For best results when cutting stone, use a diamond cutting
disc.
When using the extraction guard for cutting with a guide
block (21), the vacuum cleaner must be approved for vacu-
uming stone dust. Suitable vacuum cleaners are available
from Bosch.
The power tool must always
work in an up-grinding mo-
tion. Otherwise, there is a
risk that it will be pushed
uncontrolled out of the cut.
For best results when cut-
ting profiles and rectangular
tubing, start at the smallest
cross section.
Bosch Power Tools