IMG STAGELINE PARC-56/WS Mode D'emploi page 9

•
Always keep a minimum distance of 50 cm to the
illuminated object .
WARNING Install the spotlight safely and ex-
pertly . When installing it at a place
where people may walk or sit under it,
additionally secure it (e . g . via a safety
rope on the mounting bracket; fasten the safety
rope in such a way that the maximum falling dis-
tance of the unit will not exceed 20 cm) .
1 . Install the spotlight via its mounting brackets (7),
e . g . with a stable mounting screw or a support
for lighting units (C hook) to a cross bar .
To align the spotlight, release the two locking
screws (6) of the mounting brackets . Adjust the
desired inclination of the spotlight and fasten the
screws .
2 . Alternatively, set up the spotlight on its own: Fold
out the mounting brackets underneath the spot-
light and use them as a stand . Then fasten the
locking screws .
4.2 Colour filter and barn doors
For radiating coloured light, insert a colour filter or
a coloured filter foil (e . g . LCF-... series from IMG
STAGELINE) into the colour filter frame (4) provided .
Slide the frame into the slot at the front of the spot-
light and secure it with the clip (2) .
To reduce the light beam angle, barn doors (ac-
cessory) are available:
Barn doors
PARC-56B
PARC-64B
Insert the barn doors into the outer slot at the front of
the spotlight and secure them with the clip (2) . To ad-
ditionally secure the door barns, screw the 4 screws
supplied into the threaded holes of the door barns .
4.3 Switching on
WARNING To prevent damage to your eyes, never
look directly into the light source .
Please note that fast changes in light-
ing may trigger epileptic seizures with
photosensitive persons or persons
with epilepsy!
Connect the plug of the mains cable (5) to a mains
socket (230 V/ 50 Hz) . Thus, the spotlight is switched
on, its display (9) will indicate the menu item most
recently selected and go out after 30 seconds . As
soon as you press one of the control buttons (8), the
display will light up again for 30 seconds .
Suitable for
PARC-56 / WS
PARC-64 / WS
5 Operation
To select the operating mode and the different func-
tions, use the menu via the control buttons MENU,
ENTER, UP and DOWN (8) . Figure 2 on page 2 shows
the selection of the modes and functions via the
menu and the indications on the display (9) .
5.1 Independent operation
For independent operation, use the control buttons
(8) to set the brightness, to switch on the stroboscope
function and to set the flash rate .
1) Press the button MENU repeatedly until
appears on the display .
2) Press the button ENTER once or twice so that
the display will indicate the brightness adjusted
( ... ) .
3) To set the desired brightness, press the buttons
UP and DOWN .
4) To activate the stroboscope function, press the
button ENTER once again so that the display will
indicate .
5) To set the flash rate (
buttons UP and DOWN .
6) To change the brightness of the flash, press the
button ENTER to return to the menu item for the
brightness . To change the value, press the button
UP or DOWN .
7) To deactivate the stroboscope function, set the
flash rate to
Important: Do not exit the menu item for the bright-
ness or the flash rate with the button MENU before
switching off the spotlight . If you do, the spotlight
will remain dark when you switch it on again .
5.2 Operation with a DMX controller
For operation via a DMX light controller (e . g . DMX-
1440 or DMX-510USB), the spotlight is equipped
with four DMX control channels . DMX is short for
digital multiplex and means digital control of several
DMX units via a common control cable . The functions
of the channels and the DMX values can be found
in chapter 5 .2 .3 .
5.2.1 DMX connection
For DMX connection, 3-pole XLR connectors with the
following pin configuration are provided:
Pin 1 = ground, 2 = DMX−, 3 = DMX+
For connection, use special cables for DMX signal
transmission (e . g . cables of the CDMXN series from
IMG STAGELINE) . For cable lengths exceeding 150 m,
it is generally recommended to insert a DMX level
matching amplifier (e . g . SR-103DMX) .
... ), press the
.
9