Einhell Royal ART 14,4-1 Mode D'emploi page 15

ANLEITUNG ART 14,4-1 01023
extension system frequently.
Note
If the line is too long when you use the machine
for the first time, the surplus end of it will be cut
by the blade on the safety hood (figure 9)
If the line is too short when you start the machine
for the first time, press the knob on the line spool
and pull the line hard. When you then start the
machine for the first time the line will be cut to
the perfect length automatically (figure 10).
Remove the knife guard. Caution:
Risk of injury! Now insert the rechargeable battery
(Fig. 11). The line will be cut to the correct length
when the cutting head starts up again (Fig. 10). A
short or worn nylon line produces poor cutting
results.
Your grass trimmer will work at its best if you
observe the following instructions:
Never use the grass trimmer without its safety
devices.
Do not cut grass when it is wet. The best results
are had on dry grass.
To switch on your grass trimmer, press the safety
lock-off button (Fig. 1/Pos. 2).
To switch off your grass trimmer, let go of the
ON/OFF switch (Fig. 1/Pos. 2).
Do not move the grass trimmer against the grass
until the switch is pressed, i.e. wait until the
trimmer is running.
For the correct cutting action, swing the grass
trimmer to the side as you walk forward, holding it
at an angle of approx. 30° as you do so (see
Figure 12 and Figure 13).
Make several passes to cut long grass shorter
step by step from the top (see Figure 14).
Make full use of the guide hood in order to avoid
unnecessary line wear.
Keep the grass trimmer away from hard objects
in order to avoid unnecessary line wear.
9. Replacing the line spool
IMPORTANT! Make sure that you unplug the
rechargeable battery before replacing the line
spool (Fig. 11)!
Attach the knife guard.
Press the sides of the spool cover as shown and
remove it with the spool (Figure 7 und Figure 8).
Ensure that you do not lose the spring.
Remove the empty line spool.
Thread the ends of the line on the new line spool
11.11.2003 14:58 Uhr
through the eyelets in the spool cover (fig. 9)
Fit the spool cover and spool back into the spool
mounting.
When you start the machine again the line will be
cut to the perfect length automatically.
Remove the knife guard. Caution: Risk of
injury.
The line will be cut to the correct length when the
cutting head starts up again (Fig. 10).
Caution! Catapulted pieces of nylon line may
cause injury!
10. Charging the rechargeable battery
You can remove the rechargeable battery by
firmly pressing both locking tabs (A) while pulling
out the battery (Fig. 11).
Check to see if the voltage specified on the rating
plate of the charging unit matches the mains
voltage. Connect the power supply unit (A) to the
charging adapter (B). Plug the power supply unit
into the socket outlet. The green LED on the
charging adapter lights up (Fig. 15).
Plug the rechargeable battery (C) into the
charging adapter. The red LED on the charging
adapter lights up and shows the charging
process (Fig. 15). The time it takes to fully
recharge an empty battery is approximately 4
hours, while a partially charged battery takes
correspondingly less time. The rechargeable
battery can become a little warm during the
charging process, which is normal.
11. Cleaning and maintenance
Switch off and unplug the grass trimmer before
putting it away or cleaning it.
Remove deposits from the guard hood with a
brush.
Clean the plastic body and plastic parts with a
mild household detergent and a damp cloth.
Never use aggressive agents or solvents for
cleaning purposes!
Never spray down the grass trimmer with water.
Prevent water getting into the trimmer at all cost.
In order to make it easier for you to store the unit,
the assembled shaft can be taken apart. To do
this, firmly press both locking tabs (A) while
pulling the two shaft pieces apart from each other
(Fig. 16).
IMPORTANT: Remove the rechargeable battery
first (Fig. 11).
Seite 15
GB
15